K100-622 Aperio Cabinet Lock Series Installation Instructions HES, Inc. Phoenix, AZ 1.800.626.7590 www.hesinnovations.
System Overview The K100-622 wireless cabinet lock extends access control to a cabinet or drawer without the complexity and expense of running wires to the cabinet or drawer. The K100-622 lock connects to an access control system through the included communication hub. The communication hub connects to the access control system with wiegand wiring typical of a wiegand reader. When a credential card is presented to the reader on the lock the request for access is sent wirelessly to the communication hub.
1. Choose the hub location It is recommended that the hub be mounted near the top of a wall, on the ceiling or above the ceiling to reduce potential for interference. For a stable and reliable radio link, it is recommended that the hub is located within forty-five (45) feet of the lock.
3. Wiring the Hub. The Aperio Hub connects to the Access Control system via Wiegand wiring. The hub requires 8-24VDC power (250mA). The hub includes three form C relays that can be used to transmit latch bolt position status, low battery signal and a tamper signal. The hub connects to the cabinet lock wirelessly. *Note: The Green LED input is used to grant access to the cabinet lock.
4. Testing the Lock with the Access Control System With the hub connected to power and the access control system, test the lock with a known good credential to confirm it will open as desired when installed. 1. Remove the battery cover from the lock body 3. Connect the wire from the reader to the socket in the lock battery compartment. The wire is keyed. 2. Pass the wire and shaft from the reader through the lock body. 4. Install the batteries, ensure correct orientation.
Mounting the Lock Note regarding Orientation The K100-622 reader and lock body can be oriented in several ways to accommodate various cabinets and drawers. B C w he he 5a. Hold the lock body to the inside of the door and position it generally where you n and use a pencil ton would like it to mount. Locate lock centerline notch on the latch w he n A 5. Establish the horizontal centerline of the latch. w mark this point on the inside of the cabinet door. 5b.
. Transfer the location of the inside wall of the cabinet to the door. 6a. Measure the horizontal distance between the inside edge of the cabinet and the door edge. 6b. Using the same distance away from the door edge, draw a line on the outside surface of the door. This line depicts the location of the strike mounting surface. 6a Door edge 6b Cabinet/door front view when 7. Place and use the Lock/Reader Template. *note orientation may be reversed for right hand door 7a.
. Install the Shaft Extension. If your cabinet door thickness is greater than ½”, install the Shaft Extension to the Antenna/Reader to ensure proper engagement into the lock. Install the Shaft Extension to the shaft as shown here and firmly tighten the screw. Table 1 Shaft Extension Door Thickness Extension Shaft Used? 1/16” – ½” No > ½” – 1 ½” Yes 2-56 X 1-¼ screw (provided) 9. Install the Key Override Paddle. If a Camlock Key Override will be used, install the Key Override Paddle. 9a.
11. Install the antenna/reader. 11a. Place and hold the antenna/reader to the outside of cabinet, routing the wire through the 1/2” offset hole. 11b. Install the top screw, which attach the antenna/reader to the outside case. Refer to the table below to determine the length of the top mount screw needed, based on the thickness of the cabinet door. 11a WARNING! Make sure you avoid crimping the wires. Crimped wires may prevent the Reader and Lock from functioning. Reader mounting screw. Table 2 .
13. Electrically connect the antenna/reader wire to the lock body. Make sure to correctly orient connector while inserting it. The connector is keyed to only fit one way. 14. Install the Batteries. 14a. Gently tuck the wires into the battery cavity. 14b. Install the battery and battery cover. Note: Please verify the battery is inserted in the correct polarity position. 14c. Install and tighten the screws. 14a 14c 14b Note: Always use new batteries installed with correct polarity. 15.
16. Install the single-door strike plate. 16a. Place the strike plate over the pilot holes. Insert and tighten two screws in the slotted holes. 16b. Close the door to verify installation. Adjust the strike plate if necessary. 16c. After adjusting, insert and tighten the lock down screw on the strike plate. 16a-b 16c . Note: Do not install lock-down screw until the strike plate is correctly adjusted. OPTIONAL DOUBLE-DOOR INSTALLATION 17.
WARNING FCC Statement This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.