Item # 699 078 Model # YJAF-052-C USE AND CARE GUIDE 11 FT LED OFFSET UMBRELLA-SUNBRELLA HENNA Questions, problems, missing parts? Before returning to the store call Hampton Bay Customer Service. 8 a.m. - 7 p.m., EST, Monday - Friday, 9 a.m. - 6 p.m., EST, Saturday 1-855-HD-HAMPTON HAMPTONBAY.COM THANK YOU We appreciate the trust and confidence you have placed in Hampton Bay through the purchase of this umbrella. We strive to continually create quality products designed to enhance your home.
Table of Contents Table of Contents .......................................................... 2 Safety Information ........................................................ 2 Product Caution .......................................................................2 Safety Warnings ......................................................................2 Warranty ......................................................................... 2 What is Covered ...........................................................
Pre-Assembly PLANNING ASSEMBLY Read all instructions before assembly. To avoid damaging this product, assemble it on a soft, nonabrasive surface such as carpet or cardboard. NOTE: More than one person may be required to complete the assembly of this product. HARDWARE INCLUDED NOTE: Hardware not shown to actual size. AA BB CC Part AA Description BB M8 Washer 4+1 CC M5x8 Bolt 2+1 DD Wrench 1 EE Hex wrench S3 1 FF Hex wrench S4 1 M8x20 Hex bolt DD EE FF Quantity 4+1 3 HAMPTONBAY.
Pre-Assembly (continued) PACKAGE CONTENTS E F G D N H I C H M J J K L N P L M K K A Part O K Description B Quantity Part I J K A Lower bracket 1 B C D E Upper bracket Lower umbrella pole 1 1 1 1 F G H Crank Umbrella shade Lower base cover Locking knob Solar receiver L M N 1 1 O 2 P 4 Description Quantity Upper base cover 1 Support tube rim Corner connector Side panel Lock panel Sand bag 2 4 Replacement LED bulb Replacement lampshade 2 2 1 4 4
Assembly 1 Attaching the brackets Attach the upper bracket (B) onto the lower bracket (A). NOTE: This umbrella should be set up in its desired location to avoid moving it after assembly. B A 5 HAMPTONBAY.COM Please contact 1-855-HD-HAMPTON for further assistance.
Assembly (continued) 2 Attaching the lower umbrella pole to the brackets Attach the lower umbrella pole (C) to the upper bracket (B) and lower bracket (A) using M8x20 hex bolts (AA) and M8 washers (BB). NOTE: Fully tighten all bolts using the wrench (DD).
Assembly (continued) 3 Inserting the corner connectors Insert the corner connectors (K) into the four ends of the assembled brackets. K K K K K 7 HAMPTONBAY.COM Please contact 1-855-HD-HAMPTON for further assistance.
Assembly (continued) 4 Sliding the lock panels Slide the perforated lock panels (M) downward between the corner connectors (K).
Assembly (continued) 5 Sliding the side panels Slide the side panels (L) downward between the corner connectors (K). Connect the two pieces of the support tube rims (J). Slide the support tube rims (J) down the lower umbrella pole (C) and connect it to the brackets (A and B). NOTE: Please pay attention to the direction of the support tube rims (J). 2 J C J K K L L B A 1 K K M 9 HAMPTONBAY.COM Please contact 1-855-HD-HAMPTON for further assistance.
Assembly (continued) 6 Placing the sand bag Place the sand bag (N) in the umbrella base. NOTE: Place the base in the area where the umbrella is to be used. The umbrella will be very heavy after filled with sand.
Assembly (continued) 7 Filling the sand bag Pull to open the velcro pouch on the sand bag (N) and fill with sand. After filling the sand bags (N), close the pouch and ensure the velcro is sealed. Lock the two sections of the sand bags (N) together. NOTE: The sand bags (N) are to be filled with sand only. NOTE: For proper stability of the offset umbrella, please place 110 lbs of sand into each sand bag for a total of 220 lbs. 2 1 N 11 HAMPTONBAY.
Assembly (continued) 8 Ensuring the locking mechanism is in the open position Ensure the locking mechanism on the lock panel (M) is in the OPEN position by using the wrench (DD) as shown in figure 1. Ensure the locking mechanism on the lower base cover (H) is in the OPEN position by using the wrench (DD) as shown in figure 2. Attach the lower base cover (H) to the side panels (L). Close the lower base cover (H) and ensure they are fully closed.
Assembly (continued) 9 Locking the lower base cover Lock the lower base cover (H) and the lock panel (M) by turning the locking mechanisms to the CLOSE position using the wrench (DD) as shown in figure 1 and figure 2. Attach the upper base cover (I) to the assembled base. 2 1 DD OPEN POSITION 1 DD OPEN POSITION 2 I 3 CLOSE POSITION CLOSE POSITION H M 13 HAMPTONBAY.COM Please contact 1-855-HD-HAMPTON for further assistance.
Assembly (continued) 10 Attaching the locking knob to the lower umbrella pole Attach the locking knob (D) to the lower umbrella pole (C) using the M5x8 bolts (CC) and hex wrench S3 (EE). Make sure the locking knob (D) is placed as shown in figure (1) before attaching. NOTE: When inserting the locking knob (D) into the hole, make sure the two points of the locking knob fit into the two slots on the umbrella pole as shown below.
Assembly (continued) 11 Preparing the umbrella Push the long bent tube of the umbrella shade (G) outwards a little while holding down the tap on the short bent tube to make the hinge slide to snap into place as shown below. G 15 HAMPTONBAY.COM Please contact 1-855-HD-HAMPTON for further assistance.
Assembly (continued) 12 Attaching the solar reciever Attach the solar receiver (E) to the umbrella shade (G) by turning the solar receiver (E) clockwise until fully tightened. Insert the plug into the plug hole of the solar receiver (E). NOTE: Please leave the solar receiver (E) out in a sunny area to charge before the first time turning on the LED lights.
Assembly (continued) 13 Inserting the umbrella shade into the lower umbrella pole Rotate the locking knob (D) 180 degrees clockwise as shown in figure 1. Insert the umbrella shade (G) into the lower umbrella pole (C) as shown in figure 2. Rotate the locking knob (D) 180 degrees clockwise as shown in figure 3. NOTE: If there is a gap in the locking knob (D) as shown below in figure 3, please rotate the umbrella shade (G) until it is completely locked as shown in figure 4.
Operation 1 Attaching the crank Attach the crank (F) to the handle as shown in figure (1). Attach the crank (F) by aligning the tap with the hole on the crank (F) until it snaps into place. To detach the crank, the wrench (FF) is required to press the tap to take the crank (F) out. Attach the crank (F) without using the tap as shown in figure (2). To detach the crank (F), just take the crank out. NOTE: Both methods of attaching the crank (F) are acceptable.
Operation (continued) 2 Raising the umbrella Loosen the knob on the umbrella shade as shown in figure 1 by turning it counterclockwise until it is fully loose. Hold the umbrella handle and push the long bent tube upward as shown in figure 2 until it stops and the umbrella is fully extended. Fully tighten the knob on the umbrella shade clockwise as shown in figure 3 to lock the handle in place. 1 2 3 19 HAMPTONBAY.COM Please contact 1-855-HD-HAMPTON for further assistance.
Operation (continued) 3 Opening the umbrella Undo the Velcro belt on the canopy and shake the canopy to separate the umbrella ribs. Slowly turn the crank (F) clockwise to open the umbrella. When the umbrella is fully open, fasten the belt under the hinge of the short bent tube to stabilize the umbrella. Make sure the belt is tighten as shown in figure 3.
Operation (continued) 4 Operating the umbrella Rotate the locking knob (D) 180 degrees clockwise as shown in figure 1. Hold the umbrella handle with one hand and hold the short bent tub with the other hand to rotate the umbrella as shown in figure 2. (The umbrella can rotate up to 360 degrees.) When the umbrella is at the desired position, rotate the knob 180 degrees clockwise as shown in figure 3. Rotate the umbrella shade (G) untill the locking knob (D) automatically secures as shown in figure 4.
Operation (continued) 5 Operating the umbrella Press the ON/OFF switch to turn the LED light on and off. Fully loosen the knob on the umbrella shade (G) by turning it counterclockwise, then slide the umbrella handle down to adjust the angle of the umbrella. When the umbrella is at the desired angle to shade the sunlight, fully tighten the knob by turning it clockwise.
Operation (continued) 6 Closing the umbrella Loosen the velcro belt as shown in figure 1. Turn the crank counterclockwise to close the umbrella as shown in figure 2. When the umbrella is closed, fully loosen the knob on the umbrella shade (G) by turning it counterclockwise as shown in figure 3. Hold the handle and pull the long bent tube downward as shown in figure 4. Tighten the knob on the umbrella shade (G) by turning clockwise as shown in figure 5 after closing the umbrella.
Operation (continued) 7 Storing the umbrella Tie the umbrella to the umbrella pole with the Velcro belt when not in use as shown below. Care and Cleaning For best results, clean the frame and fabric with a damp cloth, and dry thoroughly. This will help prevent mildew by removing dirt particles that may accumulate. Do not clean with abrasive materials, bleach, or solvents. Store the umbrella in a dry, sheltered place when not in use. Tie the canopy closed on windy days to prevent damage to the umbrella.
Maintenance REPLACING THE LED LIGHTS When the light bulb does not work or a lampshade breaks, replace the light bulb or shade with the replacement light bulb (O) and the lampshade (P). Gently remove the lampshade and pull out the light bulb. Insert the replacement light bulb (O) and reinstall the lampshade. If the light does not work or illuminate after replacing, try to reverse polarity. 25 HAMPTONBAY.COM Please contact 1-855-HD-HAMPTON for further assistance.
Questions, problems, missing parts? Before returning to the store call Hampton Bay Customer Service. 8 a.m. - 7 p.m., EST, Monday - Friday, 9 a.m. - 6 p.m., EST, Saturday 1-855-HD-HAMPTON HAMPTONBAY.COM Retain this manual for future use.
