Installation Guide

ManualsBrandsHampton Bay ManualsLandscape LightingCairo Low Voltage Square Transitional Black Integrated LED Outdoor Landscape Path Light With Bubble Glass (1-Pack)

Item #1006 684 110

Model #L08457

Use and Care Guide

PACKAGE CONTENTS

Assembly and Installation

Attaching and installing the light

Connecting the wires

WARNING:

hammer to insert the spike (C) into the ground.

WARNING: The wire connector (D) contacts have sharp edges for piercing the

main low-voltage cable. To avoid injury, do not touch the metal contacts.

CAUTION: The wire from the low-voltage power unit shall be 12-18 AWG type

underground low energy circuit cable or SPT2W.

IMPORTANT:

•

building structure such as a house or deck.

• The landscape wire and connector can also be hidden under stone or buried

under grass at a maximum depth of 6 in. (15.24 cm).

•

WARNING: Risk of Electric Shock. Install all luminaires 10 ft. (3.05 m) or more

from a pool, spa or fountain.

Only for use with low voltage power units with a maximum output rating of 15V,

300W per secondary.

FOR LANDSCAPE LIGHTING SYSTEMS ONLY. OUTDOOR USE ONLY. THE DEVICE IS

ACCEPTED AS A COMPONENT OF A LANDSCAPE LIGHTING SYSTEM WHERE THE

SUITABILITY OF THE COMBINATION SHALL BE DETERMINED BY CSA OR LOCAL

INSPECTION AUTHORITIES HAVING JURISDICTIO

ETL LISTED UNDER MODEL # L08457.

Please read and save these instructions.

Part Description Quantity

Body

B 1

C 1

Post

Connector

Spike

Attach spike (C), post (B) and body (A) together by tu

Carefully remove the ﬁxture from its protective packaging.

rning them

anti clockwise.

CAUTION: Safe for outdoor operation.

WARNING

or bulb protector.

WARNING: Install in accordance with all local codes and ordinances.

INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS

IMPORTANT SAFETY INSTRUCTIONS.

Press the top half of the connector into the bottom half until it clicks

into place and is secure. This will pierce the low voltage wire and

connect the light to the transformer.

Align the low-voltage wire and ﬁt it into the connector (D) bottom

half as shown below.

Test the connection by plugging in the transformer to see if the light

turns on. If it does, unplug the transformer and continue the install-

ation. If it does not, unplug the transformer and check the connec-

tion between the transformer and low-voltage wire, reinstall the

connector, and ensure power is available to the outlet you are using.

Once the connection is secure, repeat the process for the remaining

lights.

Once all lights are connected, it is recommended to wrap each con-

nector with electrical tape for additional protection.

After

all ﬁxtures are installed, turn on the transformer by plugging it

into an outlet.

Note: If you want to install this with your existing low-voltage lighting

system, skip step 4 and instead plug the lights into your existing

- 1 -

8AWG to 12AWG SPT-2W wiring.

Caution Be careful ! The wire stabs are vert sgarp !

HB SQUARE SEEDED GLASS PATH LIGHT

Summary of content (2 pages)

PAGE 1
Item #1006 684 110 Model #L08457 Use and Care Guide HB SQUARE SEEDED GLASS PATH LIGHT Please read and save these instructions. PACKAGE CONTENTS A Part B D Description Quantity A Body 1 B Post 1 C Spike 1 D Connector 1 C Assembly and Installation 2 INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS IMPORTANT SAFETY INSTRUCTIONS. WARNING: The wire connector (D) contacts have sharp edges for piercing the main low-voltage cable.
PAGE 2
Care and Cleaning Do not use any cleaners with chemicals, solvents or harsh abrasives. Troubleshooting Problem Possible cause light Only some lights work Solution • There is no power. • There is a disconnection or break in the wire. • The transformer setting is incorrect. • Check that the power is on. • Check if there is a loose connection at the transfomer screw terminal. • Check that the power switch is not in the OFF setting. • The problem here connector.