Instructions / Assembly

ManualsBrandsHampton Bay ManualsElectronicsLow Voltage LED Marquee Path Light

Table Of Contents

Use and Care Guide

LED MOTION SENSOR

PATH LIGHTS

PACKAGE CONTENTS

A –Lamp body x 1 B – Wire Connector(with 12 in. wire attached to lamp body) C –Ground Stake (6.53 in.) x1

Per assembly and Installation

Detect

PIR deck lights pairing

Preliminary motion sensor and pairing test

- If operating only one fixture, place the fixture in its permanent location.

- To operate multiple fixtures, please pair the fixtures before installation,

follow the PAIR steps below

□

Lift the plastic cover (1) by hand, and then slided the swith (2) to the

PIR.

□ There is a DIP switch on the top of fixture, there have 4 bottons on the

switch can be slided to up and down. The fixtures with the switch

bottons in the exactly same setting will be paired as a group . Groups

can be set freely (except "0000" and "1111").

□ When at PIR off mode (0000), fixture is at off status, will not pair.

□ When at PIR test mode (1111), fixture will turn on after detecting

motion whenever at day or night, then turn off after 3S of delay.

□ If pairing lost efficacy, slided the swith (2) to the OFF, and then slided

to PIR again.

What to know before intall:

–Decide which PIR Deck Lights will be grouped (up to 10 fixtures).

–Open the plastic cover on back of each PIR Deck Light.

–Refer to the “Pairing via DIP Switch’’ Step to pair the deck lights.

–Close the plastic cover (to prevent water go inside fixture).

–When the gear is adjusted to "ON", it is "1"

- Test the motion sensor function of a single deck light.

□ Connect path light into main power cord by wire connectors.

□ Stir 4 buttons up to “ON” (Mode 1111) to make deck light on

test mode.

□ Cover the PIR sensor with light blocking object, to do

preliminary function test.

□ Remove the light blocking object, this path light will be

powered on, this means that the single path light pairing

function works.

- Test the pairing function of multiple deck lights.

□ Connect each path light into main power cord by wire

connectors (up to 10 deck lights).

□ Stir 4 buttons in any mode (except "0000" and "1111"), which

makes the path light enter the multi-lamp pairing test mode.

□ The mode of all path lights that need to be paired needs to be

set to the same.

□ Cover the PIR sensor with light blocking object to each path

lights to do preliminary function test.

□ Remove the light blocking object of one path light, this path

lights will be powered on. The rest of path lights in a group will

be sequentially powered on. This means function of motion

sensor and wirelessly link of path lights works.

General Notes:

–When the transformer is turned off the fixture light will turn

off, then PIR function become active and converts to battery

power.

–PIR Function is only active after the sensor detects the

environmental brightness at less than 50LUX at night.

–When the sensor detects the environmental brightness of less

than 50LUX, plus PIR detects motion, the deck light will turn on

and stay on for 1 minute before turning off.

–When the sensor detects the environmental brightness higher

than 200LUX, after a 90 second delay time, deck light will turn

off. The purpose of setting 90 second delay is to prevent the

200LUX brightness caused by a flash of lightning or car light.

Item # 1007 891 901

Model # KXX1501LX-01

Summary of content (9 pages)

PAGE 1
Item # 1007 891 901 Model # KXX1501LX-01 Use and Care Guide LED MOTION SENSOR PATH LIGHTS PACKAGE CONTENTS A –Lamp body x 1 B – Wire Connector(with 12 in. wire attached to lamp body) C –Ground Stake (6.53 in.) x1 Per assembly and Installation 2 Preliminary motion sensor and pairing test 1 Detect PIR deck lights pairing What to know before intall: –Decide which PIR Deck Lights will be grouped (up to 10 fixtures). –Open the plastic cover on back of each PIR Deck Light.
PAGE 2
Assembly and Installation 3 4 Connecting the wires Attaching and installing the light WARNING: The wire connector (B) contacts have sharp edges for piercing the main low voltage cable. To avoid injury, do not touch the metal contacts. WARNING: Never push the fixture into the ground by the lamp body (A) or use a hammer to insert the ground stake (C) into the ground. Insert the fixture wire on the wire connector (B) into the groove located on the top of the ground stake (C).
PAGE 3
Technical Specifications Up t SPECIFICATIONS Motion Sensor Range Up to 16.5 ft. (varies with surrounding temperature) Sensor Detection Angle 90° Power supply AC 12V Installation Height Ideally, 1.31 ft. –0.65 ft. (0.4 – 0.2 m.) above the ground. Non-replaceable battery Rechargeable Li-ion Battery 3.7V, 800mA , 2.96 Wh Charging time 4 hours at charging current 300mA SELECTING A LOCATION The motion sensor’s maximum range is 90° detection width angle (Fig. 2).
PAGE 4
Troubleshooting Problem Possible Cause The fixture will not light. □ □ □ There is no power. There is a disconnection or break in the wire. The transformer setting is incorrect. Solution □ Check the outlet and ensure that a breaker or GFCI circuit has not been tripped. □ Follow the wires from the fixture and ensure a continuous connected path back to the transformer. □ Check the settings on the transformer. The light flickers (one fixture). □ There is a loose wire connector to the fixture.
PAGE 5
Artículo # 1007 891 901 Modelo # KXX1501LX-01 GUÍA DE USO Y MANTENIMIENTO SENSOR DE MOVIMIENTO LED LUZ DE RUTA CONTENIDO DEL PAQUETE A – Estructura de la Lámpara B –Conector de Cable ( con cable de 12pulgadas fijado a la estructura de la lámpara) x1 E –Estaca de Tierra (6.53 pulgadas) Montaje e instalación preliminar 1 Detecta el emparejamiento de luces de plataforma PIR 2 Qué saber antes de la instalación: –Decida qué luz de cubierta PIR se agruparán (hasta 10 dispositivos).
PAGE 6
Montaje e Instalación (continuación) 3 4 Fijando e instalación de lámparas ADVERTENCIA: Nunca empuje la lámpara al suelo a través del estructura de la lámpara (A) o utilice un martillo para insertar la estaca de tierra (C) en el suelo. ADVERTENCIA: Los contactos del cable conector (B) tienen bordes filosos para atravesar el cable principal de bajo voltaje. No toque los contactos de metal para evitar lesiones.
PAGE 7
Especificaciones técnicas Up t ESPECIFICACIONES Rango del sensor de movimiento Hasta 16,5 pies (varía con la temperatura ambiente) Ángulo de detección del sensor 90° Fuente de alimentación AC 12V Altura de instalación Idealmente, de 0,4 a 0,2 m (1,31 pies a 0,65 pies) por encima del suelo.
PAGE 8
Solución de Problemas Problem Possible Cause El accesorio no enciende. □ □ □ No hay corriente. El cable está desconectado o roto. El transformador está mal configurado. Solution □ Verifique el tomacorriente y asegúrese que no esté apagado el interruptor o circuito GFCI. □ Siga los cables desde el accesorio y asegúrese que esté en buen estado bien conectado al transformador. □ Verifique que esté bien la configuración del transformador. La luz parpadea (en un accesorio).
PAGE 9
FCC Warning Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.