Instructions / Assembly

ManualsBrandsHampton Bay ManualsLandscape Flood LightsLow Voltage Black LED Landscape Flood Light with Adjustable Light Color and Adjustable Beam Angle

PACKAGE CONTENTS

A – Knob x1 C – Screw x1 E – Wire Connector x1 (with 12 in. F – Ground Stake (6.693 in.) x1

B – Lamp Body x1 D – Hood x1 wire attached to lamp body)

Assembly and Installation

Attaching and installing the light

Connecting the wires

WARNING: Never push the fixture into the ground by the lamp body (B)

or use a hammer to insert the ground stake (F) into the ground.

□ Insert the fixture wire on the wire connector (E) into the groove located on

the top of the ground stake (F).

□ Screw the top of the ground stake (F) into the bottom of the lamp body (B).

Ensure the fixture wire on the wire connector (E) stays in the center of the

groove on top of the ground stake (F) to avoid damage to the fixture wire.

□ Prepare a hole in the installation location. Use a tool such as a screwdriver

(sold separately) to prepare the installation hole to ensure the hole is not

larger than the ground stake (F).

□ Install the fixture in the ground by pushing on the foot step (1) on the

ground stake (F). Do not push on the lamp body (B).

□ The lamp body (B) can rotate up and down 81 degrees.

WARNING: The wire connector (E) contacts have sharp edges for

piercing the main low voltage cable. To avoid injury, do not touch the

metal contacts.

CAUTION: The wire from the low voltage power unit should be 12-16

AWG type underground low Energy Circuit Cable.

IMPORTANT:

□ Protect the wiring by routing it in close proximity to the light

fitting, or next to a building structure such as a house or a deck.

□ The landscape wire and connector can also be hidden under

stone or buried under grass at a maximum depth of 6 in. (15.24

cm).

□ Do not install the fixture within 10 ft. of a pool, spa, or fountain.

□ Do not submerge the fixture in water.

□ Place the wire connector (E) on opposite sides of the low voltage

cable (sold separately) from the transformer (sold separately) where

the fixture will be located.

□ Align and fit the main low voltage cable vertically to the slot of the

wire connector (E).

□ Press the wire connector (E) together until it is locked around the

main low voltage cable. The pre-set prongs will pierce the cable

insulation and establish contact with the electrical wire inside.

□ Once the wire connector (E) is in place, it is recommended to wrap it

with electrical tape (sold separately).

□ After all fixtures are installed, turn on the transformer.

Summary of content (7 pages)

PAGE 1
PACKAGE CONTENTS A – Knob x1 B – Lamp Body x1 C – Screw x1 D – Hood x1 E – Wire Connector x1 (with 12 in. wire attached to lamp body) F – Ground Stake (6.693 in.) x1 Assembly and Installation 2 1 Attaching and installing the light WARNING: The wire connector (E) contacts have sharp edges for piercing the main low voltage cable. To avoid injury, do not touch the metal contacts.
PAGE 2
Assembly and Installation (continued) 3 Adjusting the color temperature of the light Choose your favorite correlated color temperature (CCT) from three options: 2700K warm white, 3000K soft white, or 4000K bright white. □ Rotate the knob (A) clockwise or counterclockwise to make your selection. □ NOTICE: The factory setting for the correlated color temperature (CCT) is 3000K soft white. 4 Adjusting the beam angle of the light Loosen the screw (C).
PAGE 3
Troubleshooting Problem The fixture will not light. Possible Cause Solution □ □ There is no power. There is a disconnection or break in the wire. The transformer setting is incorrect. □ Check the outlet and ensure that a breaker or GFCI circuit has not been tripped. □ Follow the wires from the fixture and ensure a continuous connected path back to the transformer. □ Check the settings on the transformer. □ The light flickers (one fixture). □ There is a loose wire connector to the fixture.
PAGE 4
CONTENIDO DEL PAQUETE A – Perilla x1 C – Tornillo x1 B – Estructura de la Lámpara x1 D – Cubierta x1 1 E – Conector del Cable x1 (con cable de 12 pulgades fijado a la estructura de la lámpara) 2 Fijando e instalando la luz □ □ □ □ Conexión de los cables ADVERTENCIA: Los contactos del cable conector (E) tienen bordes filosos para atravesar el cable principal de bajo voltaje. No toque los contactos de metal para evitar lesiones.
PAGE 5
3 □ □ Ajuste de la temperatura de color de la luz Elija su temperatura de color correlacionada (CCT) favorita entre tres opciones: 2700K blanco cálido, 3000K blanco suave, o 4000K blanco brillante. Gire la perilla (a) en sentido horario o contrario a las manecillas del reloj para hacer su selección. AVISO: La configuración de fábrica para la temperatura de color correlacionada (CCT) es de 3000K blanco suave. 4 Ajustando el ángulo del haz de luz. Afloje el tornillo (C).
PAGE 6
Problema El accesorio no enciende. Causa Posible Solución □ □ No hay corriente. El cable está desconectado o roto. El transformador está mal configurado. □ Verifique el tomacorriente y asegúrese que no esté apagado el interruptor o circuito GFC. □ Siga los cables desde el accesorio y asegúrese que esté en buen estado bien conectado al transformador. □ Verifique que esté bien la configuración del transformador. □ La luz parpadea (en un accesorio). □ Hay algún cable conector suelto en el accesorio.
PAGE 7
FCC Warning Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.