Instructions / Assembly

ManualsBrandsHampton Bay ManualsLandscape LightingLow-Voltage 3-Watt Oil Rubbed Bronze Outdoor Integrated LED Landscape Path Lights with Crackled Shade (6-pack)

Use and Care Guide

LED LOW VOLTAGE PATH LIGHT

PACKAGE CONTENTS

A – Lamp Body x1 B – Post x1 C – Wire Connector (with 12 in. wire attached to lamp body) x1 D –Ground Stake (6.693 in.) x1

Assembly and Installation

Attaching and installing the light

Connecting the wires

WARNING: Never push the fixture into the ground by the lamp body (A)

or use a hammer to insert the ground stake (D) into the ground.

□ Screw the post (B) onto the lamp body (A).

□ Insert the fixture wire on the wire connector (C) into the groove located on

the top of the ground stake (D).

□ Screw the ground stake (D) into the post (B). Ensure the fixture wire on

the wire connector (C) stays in the center of the groove of the ground

stake (D) to avoid damage to the fixture wire.

□ Prepare a hole in the installation location. Use a tool such as a

screwdriver (not included) to prepare the installation hole to ensure that

the hole is not larger than the ground stake (D).

□ Install the fixture in the ground by pushing on the foot step (1) on the

ground stake (D). Do not push on the lamp body (A).

WARNING: The wire connector (C) contacts have sharp edges for

piercing the main low voltage cable. To avoid injury, do not touch the

metal contacts.

CAUTION: The wire from low voltage power unit should be 12-16 AWG

type underground low Energy Circuit Cable.

IMPORTANT:

□ Protect the wiring by routing it in close proximity to the light fitting,

or next to a building structure such as a house or a deck.

□ The landscape wire and connector can also be hidden under stone

or buried under grass at a maximum depth of 6 in. (15.24 cm).

□ Do not install the fixture within 10 ft. of a pool, spa, or fountain.

□ Do not submerge the fixture in water.

□ Place the wire connector (C) on opposite sides of the low voltage

cable (not included) from the transformer (not included) where the

fixture will be located.

□ Align and fit the main low voltage cable vertically to the slot of the

wire connector (C).

□ Press the wire connector (C) together until it is locked around the

main low voltage cable. The pre-set prongs will pierce the cable

insulation and establish contact with the electrical wire inside.

□ Once the wire connector (C) is in place, it is recommended to wrap it

with electrical tape (not included).

□ After all fixtures are installed, turn on the transformer.

Item #1002 669 670

Model #JAQ1501L-2/CRAC

Item #1002 669 696

Model #JAQ1501L-2/FROS

Summary of content (5 pages)

PAGE 1
Item #1002 669 670 Model #JAQ1501L-2/CRAC Item #1002 669 696 Model #JAQ1501L-2/FROS Use and Care Guide LED LOW VOLTAGE PATH LIGHT PACKAGE CONTENTS A – Lamp Body x1 B – Post x1 C – Wire Connector (with 12 in. wire attached to lamp body) x1 D –Ground Stake (6.693 in.) x1 Assembly and Installation 2 1 Attaching and installing the light WARNING: The wire connector (C) contacts have sharp edges for piercing the main low voltage cable. To avoid injury, do not touch the metal contacts.
PAGE 2
Care and Cleaning □ Clean the fixture with a soft dry cloth. □ Do not use any cleaners with chemicals, solvents or harsh abrasives. Troubleshooting Problem The fixture will not light. Possible Cause Solution □ □ There is no power. There is a disconnection or break in the wire. The transformer setting is incorrect. □ Check the outlet and ensure that a breaker or GFCI circuit has not been tripped. □ Follow the wires from the fixture and ensure a continuous connected path back to the transformer.
PAGE 3
Artículo #1002 669 670 Modelo #JAQ1501L-2/CRAC Artículo #1002 669 696 Modelo #JAQ1501L-2/FROS GUÍA DE USO Y MANTENIMIENTO LAMPARA PARA SENDAS CON LED DE BAJO VOLTAJE CONTENIDO DEL PAQUETE A – Estructura de la Lámpara x1 B - Poste x1 C – Conector de Cable (con cable de 12 pulgadas fijado a la estructura de la lámpara) x1 D – Estaca de Tierra (6.
PAGE 4
Mantenimiento y Limpieza □ Limpia la lámpara con un paño suave y seco. □ No uses limpiadores con químicos, solvents, o productos abrasivos. Solición de Problemas Problema El accesorio no enciende. Causa Posible Solución □ □ □ No hay corriente. El cable está desconectado o roto. El transformador está mal configurado. La luz parpadea (en un accesorio). □ Hay algún cable conector suelto en el accesorio. □ Verifique el tomacorriente y asegúrese que no esté apagado el interruptor o circuito GFC.
PAGE 5
FCC Warning Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.