Instructions / Assembly

ManualsBrandsHampton Bay ManualsDeck LightingBlack Integrated LED Deck Light

PACKAGE CONTENTS

A – Fixture x1 C – Wire Connector (with 36 in. wire) x1 AA – Self-Threading BB – Plastic Anchor CC – Cardboard

B – Female Plug (with 12 in. wire) x1 D – Male Plug x1 Screw (30 mm) x2 (25 mm) x2 Template x1

Installing the fixture with the wire routed behind the mounting

surface

Installing the fixture with the wire in front of the

mounting surface

NOTE: This document provides two different methods for routing the

lead wire. You can chose which method best fits your needs.

□ Place the cardboard template (CC) on the mounting surface and mark

where the holes should be for the female plug (B) and the self-threading

screws (AA).

□ Use at least a 7/16 in. drill bit to drill a hole on the surface large enough

for the female plug (B) to pass through the hole on the mounting surface.

□ Insert the female plug (B) through the hole on the mounting surface.

□ Insert the male plug (D) into the female plug (B).

□ Place the fixture (A) against the mounting surface.

□ Use a Phillips screwdriver to screw the self-threading screws (AA) through

the two holes on the fixture (A) to secure the fixture (A) to the mounting

surface.

□ Place the cardboard template (CC) on the mounting surface and

mark where the holes should be for the self-threading screws (AA).

□ Insert the male plug (D) into the female plug (B).

□ The wire plugs may be retained inside the back of the fixture (A) by

coiling the wire and plugs and dropping the wire through the notch in

the bottom of the fixture (A).

□ The wire plugs may be left outside the fixture (A) by dropping the wire

through the notch in the bottom of the fixture (A) with the plugs

outside the back plate when the fixture is mounted. The connected

plugs are waterproof.

□ Place the fixture (A) against the mounting surface.

□ Use a Phillips screwdriver to screw the self-threading screws (AA)

through the two holes on the fixture (A) to secure the fixture (A) to the

mounting surface.

Summary of content (7 pages)

PAGE 1
PACKAGE CONTENTS A – Fixture x1 B – Female Plug (with 12 in. wire) x1 C – Wire Connector (with 36 in. wire) x1 D – Male Plug x1 AA – Self-Threading Screw (30 mm) x2 BB – Plastic Anchor (25 mm) x2 CC – Cardboard Template x1 the fixture with the wire routed behind the mounting the fixture with the wire in front of the 1 Installing 1 Installing surface mounting surface □ NOTE: This document provides two different methods for routing the lead wire. You can chose which method best fits your needs.
PAGE 2
Installing the fixture on a surface using plastic anchors If installation requires the plastic anchors (BB), then place the cardboard template (CC) on the mounting surface and mark where the holes should be for the self-threading screws (AA). □ At those marks, use a 15/64 drill bit (or 6 mm) to drill two holes in the mounting surface. □ Push the plastic anchors (BB) into the two holes until the heads of the plastic anchors (BB) are flush with the mounting surface.
PAGE 3
□ Clean the fixture with a soft dry cloth. Problem The fixture will not light. Possible Cause □ □ □ There is no power. There is a disconnection or break in the wire. The transformer setting is incorrect. □ Do not use any cleaners with chemicals, solvents or harsh abrasives. Solution □ Check the outlet and ensure that a breaker or GFCI circuit has not been tripped. □ Follow the wires from the fixture and ensure a continuous connected path back to the transformer.
PAGE 4
CONTENIDO DEL PAQUETE A –Dispositivo de Iluminación x1 C –Conector Cable (con un cable de 36 pulgadas) x1 AA– Tornillos BB – Anclas de CC – Plantilla de B –Enchufe Hembra (con un D – Enchufe Macho x1 Autorroscantes (30mm) x2 Plastico (25mm) x2 Cartón x1 cable de 12 pulgadas) x1 1 Instalando el dispositivo de iluminación con el cable enrutado detrás de la superficie de montaje NOTA: Este documento proporciona dos métodos diferentes para enrutar el cable conductor.
PAGE 5
Instale el dispositivo de iluminación en una superficie con anclajes de plástico 2 Conexión de los cables Si la instalación requiere de anclajes de plástico (BB), coloque la plantilla de cartón (CC) en la superficie de montaje y marque los orificios para los tornillos de autorroscantes (AA). □ En esas marcas, use una broca de 15/64 (o 6 mm) para perforar dos orificios en la superficie de montaje.
PAGE 6
□ Limpia la lámpara con un paño suave y seco. □ No uses limpiadores con químicos, solvents, o productos abrasivos. Problema El accesorio no enciende. Causa Posible Solución □ □ □ No hay corriente. El cable está desconectado o roto. El transformador está mal configurado. La luz parpadea (en un accesorio). □ Hay algún cable conector suelto en el accesorio. □ Verifique el tomacorriente y asegúrese que no esté apagado el interruptor o circuito GFC.
PAGE 7
Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.