Warranty

ManualsBrandsHampton Bay ManualsOutdoor Heating38,200 BTU Bronze Heat-Focusing Propane Gas Patio Heater

Assembly & User Instructions

Mirage 38,200Btu

Heat Focusing Patio Heater

These instructions are for your safety. Please read them

thoroughly before use and retain them for future reference.

DANGER:

If you smell gas:

1. Shut o gas to the appliance.

2. Extinguish any open ame.

3. If odor continues, keep away from

the appliance and immediately call

your gas supplier or re department.

WARNING:

Do not store or use gasoline or other

ammable vapors and liquids in the

vicinity of this or any other appliance.

An LP-cylinder not connected for use

shall not be stored in the vicinity of any

other appliance.

WARNING:

For Outdoor Use Only.

WARNING:

Improper installation, adjustment,

alteration, service or maintenance can

cause injury or property damage.

Read the installation, operating and

maintenance instructions thoroughly

before installing or servicing this

equipment.

We provide a Customer Support Service.

If you have any queries please contact us

on info@uigroup.ie or tel. (678) 534 2876

or visit our website www.uigroup.ie

Patent No: US 8,176,910

You will nd product assembly/demonstration videos on our website:

www.uigroup.ie/product-demonstrationstutorial-videos

Summary of content (18 pages)

PAGE 1
Assembly & User Instructions Mirage 38,200Btu Heat Focusing Patio Heater These instructions are for your safety. Please read them thoroughly before use and retain them for future reference. DANGER: If you smell gas: 1. Shut off gas to the appliance. 2. Extinguish any open flame. 3. If odor continues, keep away from the appliance and immediately call your gas supplier or fire department.
PAGE 2
Parts Supplied Ref Description 1 Base 2 Cylinder Chamber Supports 3 Cylinder Chamber Door 4 Cylinder Chamber Wall Illustration Qty 1 Ref 7 Description Lower Support Pole 3 8 Upper Support Pole 1 9 Lantern Illustration Qty 1 1 1 1 10 Parasol Side Panels 5 Cylinder Chamber Top 1 11 Parasol Top Panel 1 6 Reflector Handle 1 12 Regulator 1 Page 1 6
PAGE 3
Fixings Supplied Ref Description Illustration Qty Ref A 1/4″ Dome Head Bolt 27 D 1/4″ Washer 7 B 1/4″ Nut 33 E 5/16″ Washer 3 C 1/4″ Hex Bolt 19 F 5/16″ Bolt 3 G 1/4″ Spring Washer 7 Fixings are shown at actual size. Description Illustration Qty Before You Start • Check the contents of the box and make sure you have all the parts and fittings listed. If not, contact the factory by email: info@uigroup.
PAGE 4
Assembly Step 1 Base Cylinder Chamber Supports (A,B,C) 1/4″ Hex Bolt (C) Fix the cylinder chamber supports (A,B,C) to corresponding location on the base with 6 of the 1/4″ hex bolts (Ref. C). Finger tighten only.
PAGE 5
Assembly Step 2 Lower Support Pole 1/4″ Nut (B) 1/4″ Hex Bolt (C) Fix lower support pole to cylinder chamber supports as shown using 6 of the 1/4″ hex bolts (Ref. C) and 6 of the 1/4″ nuts (Ref. B). Finger tighten only.
PAGE 6
Assembly Step 3 Cylinder Chamber Wall 1/4″ Dome Head Bolt (A) 1/4″ Nut (B) Fit the cylinder chamber wall to the cylinder chamber supports using 6 of the 1/4″ dome head bolts (Ref. A) and 6 of the 1/4″ nuts (Ref. B). Finger tighten only.
PAGE 7
Assembly Step 4 Cylinder Chamber door Hang door on hinges. Ensure correct alignment and tighten all bolts securely.
PAGE 8
Assembly Step 5 Cylinder Chamber Top 1/4″ Dome Head Bolt (A) 1/4″ Nut (B) Fit cylinder chamber top onto cylinder chamber support legs using 3 of the 1/4″ dome head bolts (Ref. A) and 3 of the 1/4″ nuts (Ref. B).
PAGE 9
Assembly Step 6 1/4″ Hex Bolt (C) 1/4″ Washer (D) 1/4″ Spring Washer (G) Fit upper support pole to lower support pole using 3 of the 1/4″ hex bolts (Ref.C) and spring washers (Ref.G) and washers (Ref.D).
PAGE 10
Assembly Step 7 1/4″ Hex Bolt (C) 1/4″ Washer (D) 1/4″ Spring Washer (G) Battery Feed the lantern hose down the support pole and secure lantern to support pole using 4 of the 1/4″ Hex Bolts (Ref. C) and spring washers (Ref. G) and washers (Ref. D). Lantern 1/4″ Washer (D) Sparker Button 1/4″ Hex Bolts (C) 1/4″ Spring Washer (G) 1/4″ Hex Bolt (C) Unscrew sparker button and insert battery, positive side facing outwards.
PAGE 11
Assembly Step 8 First, connect hose to regulator securely using adjustable wrenches Second, screw regulator onto gas cylinder Regulator Position gas cylinder inside cylinder chamber as shown securing with chain. Connect the lantern hose to the regulator hose and secure tightly with adjustable wrenches. Then attach the regulator to the cylinder, turn clockwise to tighten it securely. Place cylinder in position as shown.
PAGE 12
Assembly Step 9 Reflector handle Fitting reflector handle Using the pre-fitted R-clip and pin, secure the reflector handle to the bracket as shown.
PAGE 13
Assembly Step 10 Top Panel Side Panels 5/16″ Bolt (F) 5/16″ Washer (E) 1/4″ Dome Head Bolt (A) 1/4″ Nut (B) Loosely screw parasol side panels together using 12 of the 1/4″ Dome Head Bolts (Ref. A) and 1/4″ Nuts (Ref. B) overlapping as shown below. Fix the top panel to the top of the assembled side panels using 6 of the 1/4″ Dome Head Bolts (Ref. A) and 1/4″ Nuts (Ref. B) and then fully tighten all bolts.
PAGE 14
For all appliances: • The heater, when installed, must be electrically grounded in accordance with local codes or, in the absence of local codes, with the National Electrical Code, ANSI/NFPA 70, or the Canadian Electrical Code, CSA C22.1. • Certain materials or items, when stored under the heater, will be subjected to radiant heat and could be seriously damaged. • Inspect the visible portion of the hose before each use of the appliance.
PAGE 15
Leak Testing Testing Leak To be be performed performed in in a a well well ventilated ventilated area. area. •• To •• Confirm Confirm all all control control knobs knobs are are in in the the off off position. position. •• Open Open the the gas gas control control valve valve on on the the bottle. bottle.
PAGE 16
Use Instructions Before proceeding make sure you understand the warnings section of this manual. Lighting instructions: • Fit battery to sparker. • Turn on gas supply at cylinder. • Push dial in and turn to position . • While dial is held pressed in at position , press spark button to ignite the heater. • Hold dial in for at least 10 seconds to ensure heater stays lit. • If heater does not light after holding dial in for 20 seconds wait 5 minutes and try again.
PAGE 17
• When using the heater after extended periods of storage, re-attach the reflector. The heater should never be operated without the reflector in place. • If the heater is to be stored indoors, the gas bottle must be disconnected and left outside in a dry, well-ventilated area, away from any sources of heat or ignition. • Do not let children tamper with the bottle. Service If your heater needs maintenance or is not working properly, please contact your local authorized agent for service.
PAGE 18
CAUTION • It is normal for the heater to smoke during the first few minutes of use. • If you smell gas – turn off the appliance and extinguish all flames. If the odour continues, immediately contact your gas supplier. • In the event of an uncontrollable fire, immediately disconnect the gas cylinder moving it away from fire and contact the fire services. DO NOT PUT YOURSELF AT RISK! • Ensure aerosols are not used near this unit when in use. • Ensure all packaging and plastic bags are disposed of safely.