Instructions / Assembly

ManualsBrandsHampton Bay ManualsOutdoor Heating38,200 BTU Bronze Heat-Focusing Propane Gas Patio Heater

Assembly & User Instructions

Mirage 38,200Btu

Heat Focusing Patio Heater

These instructions are for your safety. Please read them

thoroughly before use and retain them for future reference

DANGER:

If you smell gas:

1. Shut off gas to the appliance.

2. Extinguish any open flame.

3. If odor continues, keep away from the

appliance and immediately call your gas

supplier or fire department.

WARNING:

Do not store or use gasoline or other

flammable vapors and liquids in the vicinity

of this or any other appliance.

An LP-cylinder not connected for use shall

not be stored in the vicinity of any other

appliance.

WARNING:

For Outdoor Use Only.

WARNING:

Improper installation, adjustment, alteration,

service or maintenance can cause

injury or property damage.

Read the installation, operating and

maintenance instuctions thoroughly before

installing or servicing this equipment.

e pr

ovide a

Customer Suppor

t Ser

vice

If you have any queries please contact us

on info@uig.biz or tel. (678) 534 2876

or visit our website www.uig.biz

Summary of content (18 pages)

PAGE 1
Assembly & User Instructions Mirage 38,200Btu Heat Focusing Patio Heater These instructions are for your safety. Please read them thoroughly before use and retain them for future reference DANGER: If you smell gas: 1. Shut off gas to the appliance. 2. Extinguish any open flame. 3. If odor continues, keep away from the appliance and immediately call your gas supplier or fire department.
PAGE 2
Parts Supplied Ref Description 1 Base Upper & Lower Cylinder Chamber 2 Supports A,B and C Illustration Qty Ref Description Illustration Qty 1 7 Lower Support Pole 1 3 8 Upper Support Pole 1 ABC 3 Cylinder Chamber Door 1 9 Lantern 1 4 Cylinder Chamber Wall 1 10 Parasol Side Panels 6 5 Cylinder Chamber Top 1 11 Parasol Top Panel 1 6 Reflector Handle 1 12 Regulator 1 Page 1
PAGE 3
Fixings Supplied Ref Description A M6 Nut illustration Qty Ref Description illustration Qty 33 D M8 Washer 3 E M8x10 Bolt 3 B M6x10 Dome Head Bolt 27 C M6x12 Dome Hex Bolt 19 Before You Start • Check the contents of the box and make sure you have all the parts and fittings listed. If not, contact the Factory by email: info@uig.
PAGE 4
Assembly step 1 Base x 1 Upper & Lower Cylinder Chamber Supports (A,B,C) M6 Bolt (C) Fix the cylinder chamber supports. (A,B,C) to corresponding location on the base with 6 M6 bolts (Ref. C).
PAGE 5
Assembly step 2 Lower Support Pole M6 Nut (A) M6x12 Dome Hex Bolt (C) Fix lower support pole to cylinder chamber supports as shown using 6 M6 bolts (Ref. C) and 6 M6 nuts (Ref.
PAGE 6
Assembly step 3 Cylinder Chamber Wall M6x10 Dome Head Bolt (B) M6Nut (A) Fit the cylinder chamber wall to the cylinder chamber supports using 6 dome head bolts (Ref. B) and 6 M6 nuts (Ref.
PAGE 7
Assembly step 4 Cylinder Chamber door Hang door on hinges. Ensure correct alignment and tighten bolts securely.
PAGE 8
Assembly step 5 Cylinder Chamber Top M6 x 10 Dome Bolt (B) M6 Nut (A) Fit cylinder chamber top onto cylinder chamber support legs using 3 dome head bolts (Ref. B) and M6 nuts (Ref.
PAGE 9
Assembly step 6 M6 x 12 Dome Hex Bolt (C) Fit upper support pole to lower suport pole using 3 x m6x12 dome hex bolts (Ref.
PAGE 10
Assembly step 7 M6 x 12 Dome Hex Bolt (C) 1. Feed the lantern hose down the support pole and secure lantern to support pole using 4 M6x12 Dome Hex Bolts. (Ref.
PAGE 11
Assembly step 8 Regulator Connect the lantern hose to the regulator hose and secure tightly with adjustable wrenches. Then attach the regulator to the cylinder, turn clockwise to tighten it securely. Place cylinder in position as shown. Connect securely with adjustable wrenches Check for Leak Your patio heater has been checked at all factory connections for leakage. To check the connection at the gas hose/regulator/cylinder 1. Make leakage solution by mixing 50% water with 50% liquid dish soap. 2.
PAGE 12
Assembly step 9 Reflector handle Fitting reflector handle 1 2 R Clip Retaining Pin Heat focus reflector bracket Remove R clip and retaining pin Reflector handle Fit reflector handle 3 Secure with retaining pin and R clip.
PAGE 13
Assembly step 10 Top Panel Side Panels M8x10 Bolt (E) M8 Washer (D) Dome Head Bolt (B) M6 Nut (A) Remove any protective layer and loosely screw parasol side panels together overlapping as shown with 18 dome head bolts and nuts (B,A), fix the top panel to the top of assembled side panels. Tighten all nuts. Fix assembled parasol onto top of Parabolic Reflector Bracket using 3 M8x10 Bolts (E) and M8 washers (D).
PAGE 14
For all appliances: • The heater, when installed, must be electrically grounded in accordance with local codes or, in the absence of local codes, with the National Electrical Code, ANSI/NFPA 70, or the Canadian Electrical Code, CSA C22.1. • Certain materials or items, when stored under the heater, will be subjected to radiant heat and could be seriously damaged. • Inspect the visible portion of the hose before each use of the appliance.
PAGE 15
Leak Testing • To be performed in a well ventilated area. • Confirm all control knobs are in the off position. • Open the gas control valve on the bottle or regulator. • Check the leaks by brushing a solution of 1/2 water and 1/2 soap over the gas system joints, including all valve connections, hose connections and regulator connections. • NEVER USE AN OPEN FLAME to test for leaks at any time. • If bubbles form over any of the joints, there is a leak. • Turn off gas supply and retighten all joints.
PAGE 16
Use Instructions Before proceeding make sure you understand the warnings section of this manual. Lighting instructions: • Turn on gas supply at cylinder. • Push dial in and turn to position . • While dial is held pressed in at position , press spark button repeatedly to ignite the burner. • Hold dial in for at least 10 seconds to ensure heater stays lit. • If burner does not light after holding dial in for 20 seconds wait 5 minutes and try again.
PAGE 17
• When using the heater after extended periods of storage, re-attach the reflector. The heater should never be operated without the reflector in place. • If the heater is to be stored indoors, the gas bottle must be disconnected and left outside. in a dry, well-ventilated area,away from any sources of heat or ignition. • Do not let children tamper with the bottle. Service If your heater needs maintenance or is not working properly, please contact your local authorized agent for service.
PAGE 18
CAUTION • It is normal for the heater to smoke during the first few minutes of use. • Regularly clean your patio heater after every use. • If you smell gas – turn off the appliance and extinguish all flames. If the odour continues, immediately contact your gas supplier. • In the event of an uncontrollable fire, immediately disconnect the gas cylinder moving it away from fire and contact the fire services. DO NOT PUT YOURSELF AT RISK! • Ensure aerosols are not used near this unit when in use.