Item #1002693243 Model #HDMIRAGECO PC Use and Care Guide 48,000 COMMERCIAL GRADE HEAT FOCUSING PATIO HEATER Questions, problems, missing parts? Before returning to the store, call our Customer Service (678) 534 2876
Table of Contents Table of Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Safety Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3 Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Pre-Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Safety Information (continued) WARNING: ONLY use this appliance on a flat LEVEL non flammable surface or ground. WARNING: In the event of an uncontrollable fire, immediately disconnect the gas cylinder moving it away from fire and contact the fire services. DO NOT PUT YOURSELF AT RISK! WARNING: When positioning, ensure the unit is a minimum of 40 inches (1m) from flammable items or structure from all sides and above. WARNING: Ensure aerosols are not used near this unit when in use.
Warranty Warranty Keep these instructions for future reference. The patio heater has been manufactured under the highest standards of quality and workmanship. We warrant to the original consumer purchaser that all aspects of this product will be free of defects in material and workmanship for 1 year from the date of purchase. A replacement for any defective part will be supplied free of charge for installation by the consumer.
Pre-Assembly PLANNING ASSEMBLY Before You Start, check the contents of the box and make sure you have all the parts and fittings listed. If not, contact our Customer Service at (678) 534 2876. When you are ready to start, make sure that you have the right tools at hand, plenty of space and a clean dry area for assembly. Warning: While every precaution has been made in the manufacture of this product, care must be taken during assembly in case sharp edges are present.
Pre-Assembly (continued) Package Contents N O K M J F B I L D G E H C A Part A B C D E F G H Part I J K L M N O Quantity Description 1 Base 6 Upper & Lower Cylinder Chamber Supports (A, B, C) 1 Base Plate 1 Upper Cylinder Chamber Wall 1 Lower Cylinder Chamber Wall 1 Lower Support Pole 1 Upper Cylinder Chamber Door 1 Lower Cylinder Chamber Door 6 Description Table Top Upper Support Pole Lantern And Hose Regulator Reflector Handle Top Panel Side Panels Quantity 1 1 1 1 1 1 6
Pre-Assembly (continued) technical data Overall Height Overall Weight Overall Width Heater Heat Input (·Qn) Heater Gas Consumption Heater Injector Size Setting Pressure Regulator Outlet Pressure Standard Gas Supply Pressure 93.5 in. approx. 124 lbs 38.5 in. 48,000 Btu/h 2.20 Lbs per hour 0.08 in. 11.0 in. per W.C 11.0 in. per W.C ANSI Z83.26-2014 • CSA2.37-2014 Gas Fired Outdoor infrared Patio heaters Max. 250 PSI, MIN.
Assembly 2 Attaching the cylinder chamber walls 1 Assembling the legs □□ Using 11 of the bolts (AA) and nuts (BB), attach the lower cylinder chamber wall (E) to the bottom of the cylinder chamber supports (B) and attach the upper cylinder chamber wall (D) by overlapping the lower cylinder chamber wall (E) as shown. □□ Attach the base plate (C) to the base (A) using the two prefitted bolts. □□ Attach the upper and lower cylinder chamber supports (B) together using six bolts (CC) and nuts (BB).
Assembly (continued) 4 Attaching the cylinder chamber door 3 Attaching the lower support pole □□ Attach the upper cylinder chamber door panel (G) to the lower cylinder chamber door panel (H) using three bolts (AA) and nuts (BB). □□ Attach the lower support pole (F) to the cylinder chamber supports (B) using six bolts (CC) and nuts (BB). □□ At this point ensure that all bolts are tightened securely using a spanner. □□ Hang the assembled door on the hinges.
Assembly (continued) 5 table Attaching the upper support pole and 6 Attaching the lantern top □□ Feed the hose down through the support pole (J) and secure the lantern (K) to the support pole (J) using four bolts (CC), washers (DD) and spring washers (GG). □□ Slide the table top (I) down over the lower support pole (F) as shown and secure to the cylinder chamber supports (B), using three bolts (CC) and three washers (DD).
Assembly (continued) 8 Fitting the reflector handle 7 bottle Attaching the regulator and propane □□ Using the pre-fitted R-clip (1) and pin (2), secure the reflector handle (M) to the bracket as shown. NOTE: The cylinder must be positioned as shown in the patio heater cylinder chamber to provide vapor withdrawal. □□ Connect the lantern and hose (K) to the regulator (L) and secure tightly with the adjustable wrenches.
Assembly (continued) 10 lantern Attaching the reflector to the 9 Assembling the reflector Warning: While every precaution has been made in the manufacture of this product, care must be taken during assembly in case sharp edges are present. □□ Fit the reflector to the lantern (K) using three bolts (FF) and washers (EE). □□ Loosely screw the reflector side panels (O) together using twelve bolts (AA) and nuts (BB), overlapping as shown below.
Operation □□ The heater, when installed, must be electrically grounded in accordance with local codes or, in the absence of local codes, with the National Electrical Code, ANSI/NFPA 70, or the Canadian Electrical Code, CSA C22.1. □□ Certain materials or items, when stored under the heater, will be subjected to radiant heat and could be seriously damaged. □□ Inspect the visible portion of the hose before each use of the appliance.
Operation (continued) □□ Important - Make sure the gas bottle is placed level within the base. □□ Should you need to change the gas bottle, confirm the gas supply is turned off at the regulator or bottle / cylinder valve, and there are no sources of ignition (cigarettes, open flame, sparks, etc.) near before proceeding. □□ Inspect the gas hose to ensure it is free from any twisting or tension. The hose should hang freely with no bends, folds, or kinks that could obstruct free flow of gas.
Operation (continued) leak testing Your patio heater has been checked at all factory connections for leakage. To check the connection at the gas hose/regulator/cylinder: □□ Ensure you are in a well ventilated area. □□ Confirm all control knobs are in the off position. □□ Open the gas control valve on the bottle. □□ Check for leaks by brushing a solution of 50% water and 50% dish soap over the gas system joints, including all valve connections, hose connections and regulator connections.
Maintenance FLAME CHARACTERISTIC □□ The flame pattern at the burner mesh should be visually checked whenever the heater is operated. □□ Normally, the burner flame is blue with yellow flame at the top. The burner mesh will become red hot. □□ If flames extend beyond the surface of the burner mesh, or there is the phenomena of flame lift or light back, or a black spot is accumulating on the burner mesh or reflector, the heater should be turned off immediately.
Questions, problems, missing parts? Before returning to the store, call our Customer Service (678) 534 2876 Retain this manual for future use.