Item Model 1000 053 245 HB1023C-35DISP Item Model 1000 053 230 HB1023C-35 USE AND CARE GUIDE ____________________________________ LED CEILING FLUSH MOUNT Questions, problems, missing parts? Before returning to the store, call Hampton Bay Customer Service 8 a.m. – 6 p.m., EST, Monday – Friday 1-855-HD-HAMPTON HAMPTONBAY.COM THANK YOU We appreciate the trust and confidence you have placed in Hampton Bay through the purchase of this LED ceiling flush mount.
Table of Contents Table of Contents Safety Information Warranty Pre-Installation Planning the Installation Tools Hardware Package Contents 2 2 2 3 3 3 3 4 Installation Operation Care and Cleaning Exterior Maintenance Interior Maintenance FCC Notice Dimming Troubleshooting 5 7 7 7 7 7 8 8 Safety Information Before starting installation of this fixture or removal of a previous fixture, disconnect the power by turning off the circuit breaker or by removing the fuse at the fuse box.
Pre-Installation PLANNING THE INSTALLATION Read all instructions before assembly and installation. Before starting installation of the fixture or removal of a previous fixture, disconnect the power by turning off the circuit breaker or by removing the fuse at the fuse box. To avoid damaging this product, assemble it on a soft, non-abrasive surface such as carpet or cardboard. NOTE: Keep your receipt and these instructions for Proof of Purchase.
Pre-Installation (continued) PACKAGE CONTENTS B A C Part Description Quantity A Glass Shade 1 B Fixture Pan 1 C Frame 1 4
Installation 1 Mounting the hardware Thread the mounting screws (BB) into the outlet box so that they extend approximately 1/2 in. below the ceiling. BB 2 Connecting the wires NOTE: If you have electrical questions consult your local electrical code for approved grounding methods. Pull the power supply wires out from the outlet box. Connect the black supply wire to the black fixture wire using wire nuts (AA). Connect the white supply wire to the white fixture wire using wire nuts (AA).
Installation (continued) 3 Securing the fixture pan Carefully tuck all the wires and wire connections into the outlet box. Place the fixture pan (B) over the outlet box and feed the mounting screws (BB) through the keyhole slots. B Rotate the fixture pan (B) so that the mounting screws (BB) slide into the narrow ends of the keyhole slots. Bottom View Tighten the mounting screws (BB) so that the fixture pan (B) is secured flush against the ceiling.
Operation Turn on power at the circuit breaker or fuse box. Turn the light switch on to activate the fixture. Care and cleaning EXTERIOR MAINTENANCE NOTE: Do not use any cleaners with chemicals, solvents, or harsh abrasives. Use only a dry soft cloth to dust or wipe carefully. Use a dry or slightly dampened clean cloth and wipe the surface of the fixture. INTERIOR MAINTENANCE Disconnect power to the fixture by turning off the circuit breaker or by removing the fuse at the fuse box.
Dimming For a complete list of compatible dimmers, please look up the item number listed on the cover of this instruction manual at www.hamptonbay.com Troubleshooting Problem Solution The light will not turn on. The fuse blows or circuit breaker trips when light is turned on. Check the wire connections 8 Make sure the power supply is on. Test or replace the switch. Check the wiring. Replace the driver.
This page is intentionally left blank. 9 HAMPTONBAY.COM Please contact 1-855-HD-HAMPTON for further assistance.
Questions, problems, missing parts? Before returning to the store, call Hampton Bay Customer Service 8 a.m. – 6 p.m., EST, Monday-Friday 1-855-HD-HAMPTON HAMPTONBAY.COM Retain this manual for future use.
Artículo Modelo 1000 053 245 HB1023C-35DISP Artículo Modelo 1000 053 230 HB1023C-35 GUÍA DE USO Y MANTENIMIENTO ____________________________________ LUMINARIO DE TECHO CON LUZ LED Preguntas, problemas, o piezas faltantes? Antes de regresar a la tienda, llama al Servicio al Cliente de Hampton Bay 8 a.m. – 6 p.m., Hora del Este, Lunes – Viernes 1-855-HD-HAMPTON HAMPTONBAY.
Tabla de Contenidos Tabla de Contenidos Información de Seguridad Garantía Pre-Instalación Planificación de la Instalación Herramienta Ferretería Contenido del Paquete 12 12 12 13 13 13 13 14 Instalación Operación Cuidado y Limpieza Mantenimiento Exterior Mantenimiento Interior Aviso de FCC Atenuación Solución de Problemas 15 17 17 17 17 17 18 18 Información de Seguridad Antes de iniciar la instalación de este aparato o la eliminación de un accesorio anterior, desconecte la alimentación apagando el di
Pre-Instalación PLANIFICACIÓN DE LA INSTALACIÓN Lea todas las instrucciones antes del montaje e instalación. Antes de comenzar la instalación de la luminaria o el retiro de un artefacto anterior, desconecte la alimentación apagando el disyuntor o quitando el fusible en la caja de fusibles. Para evitar daños a este producto, montarlo en una superficie suave y no abrasiva, como una alfombra o cartón. NOTA: Guarde su recibo y estas instrucciones para comprobante de compra.
Pre-Instalación (continuado) CONTENIDO DEL PAQUETE B A C Parte Descripción Cantidad A Pantalla de Vidrio 1 B Base del Luminario 1 C Armazón 1 14
Instalación 1 Montaje de ferretería Enrosque los tornillos de montaje (BB) en la caja de distribución para que sobresalgan aproximadamente 1/2 pulgada debajo del techo. BB 2 Conexiones de cables NOTA: Si tiene dudas con las conexiones eléctricas, consulte el código eléctrico de su localidad para los métodos aprobados de conexione a tierra. Saque los cables de alimentación de la caja de distribución.
Instalación (continuado) 3 Asegurando la base del luminario Meta con cuidado todos los cables y conexiones de cables en la caja de distribución. Coloque la base del luminario (B) sobre la caja de distribución y en los tornillos de montaje (BB) pasando por los agujeros de bocallave. Gira la base del luminario (B) en una dirección, de tal manera que los tornillos de montaje (BB) se deslicen por los extremos estrechos de los agujeros de bocallave.
Operación Conecte la alimentación en el disyuntor o caja de fusibles. Gire el interruptor de la luz para activar el aparato. Cuidado y Limpieza MANTENIMIENTO DEL EXTERIOR NOTA: No use limpiadores con químicos, solventes o abrasivos fuertes. Use sólo un paño seco para sacudir o limpiar con cuidado. Use un paño limpio y seco o ligeramente humedecido y limpie la superficie de la linterna.
Atenuación Para una lista completa de atenuadores compatibles, por favor a el numero de articulo que aparece en la primera pagina de este manual de instrucciones en www.hamptonbay.com Solución de Problemas Problema Solución La luz no se enciende. Asegúrese de que la energía eléctrica esté encendida. Pruebe o cambie el interruptor. Verifique los cableado. Reemplace el controlador. El fusible se funde o el disyuntor de circuitos se dispara cuando se enciende la luz.
Esta página ha sido dejada en blanco intencionalmente. 19 HAMPTONBAY.
Preguntas, problemas, o piezas faltantes? Antes de regresar a la tienda, llama al Servicio al Cliente de Hampton Bay 8 a.m. – 6 p.m., Hora del Este, Lunes – Viernes 1-855-HD-HAMPTON HAMPTONBAY.COM Conserve este manual para futuras consultas.
Article Modèle 1000 053 245 HB1023C-35DISP Article Modèle 1000 053 230 HB1023C-35 GUIDE D'UTILISATION ET D'ENTRETIEN ____________________________________ PLAFONNIER DEL Questions, problèmes, pièces manquantes? Avant de retourner au magasin, appeler Hampton Bay Service à la clientèle 8:00 – 18:00, HNE, Lundi – Vendredi 1-855-HD-HAMPTON HAMPTONBAY.COM MERCI Nous apprécions la confiance que vous avez placée dans Hampton Bay grâce à l'achat de cette planfonnier DEL.
Table of Contents Table of Contents Consignes de Sécurité Garantie Pré-Installation Planification du l’Installation Outils Matériel Contenu du Paquet 22 22 22 23 23 23 23 24 Installation Opération Entretien et Nettoyage Entretien Extérieur Entretien Intérieur Avis de la FCC Gradation de L'intensité Lumineuse Dépannage 25 27 27 27 27 27 28 28 Consignes de Sécurité Avant de commencer l'installation de ce luminaire ou à la dépose d'un précédent luminaire, débrancher l'alimentation en désactivant le disj
Pré-Installation PLANIFICATION DE L'INSTALLATION Lire toutes les instructions avant assemblage et l’installation. Avant de commencer l'installation du luminaire ou la dépose d'un précédent luminaire, débrancher l'alimentation en désactivant le disjoncteur ou en retirant le fusible de la platine de fusibles. Pour éviter d'endommager le produit, assembler sur un doux et non abrasif surface tels que tapis ou un morceau de carton. NOTE: Conservez votre reçu et ces instructions à la preuve d'achat.
Pré-Installation (continue) CONTENU DU PAQUET B A C Partie Description Quantité A Abat-jour en Verre 1 B Plaque de Montage 1 C Cadre 1 24
Installation 1 Le montage du matériel Enfilez les vis de montage (BB) dans la boîte de sortie de manière à ce qu'elles s'étendent environ 1,27 cm en dessous du plafond. BB 2 La connexion des fils NOTE: Si vous avez des questions concernant l’installation électrique, veuillez consulter le code de l’électricité en vigueur dans votre province pour connaître les méthodes de mise à la terre approuvées. Tirez les fils d’alimentation hors de la boîte de sortie.
Installation (continue) 3 Sécurisation de le plaque de montage Rentrez soigneusement tous les fils et les connexions à l’intérieur de la boîte de sortie. Placez le plaque du luminaire (B) sur la boîte de sortie en faisant passer les vis du luminaire (BB) par les encoches en trou de serrure. B Faites tourner le plaque du luminaire (B) de manière que les vis du luminaire (BB) glissent jusqu’à l’extrémité la plus étroite des encoches en trou de serrure.
Opération Mettez sous tension au niveau du disjoncteur ou des fusibles. Allumez l'interrupteur pour activer l'appareil. Entretien et Nettoyage ENTRETIEN EXTÉRIEUR NOTE: N’utilisez aucun produit de nettoyage contentant des agents chimiques, des solvants ou des abrasifs durs. Utilisez uniquement un linge doux et sec pour enlever la poussière en essuyant délicatement Utilisez un linge sec ou légèrement humide et essuyez le luminaire.
Gradation de L’intensité Lumineuse Pour une liste complète des gradateurs compatibles, consultez le numéro article sur la couverture de ce manuel d'instructions à www.hamptonbay.com. Dépannage Problème Solution La lumière ne s'allume pas. Le fusible brûle ou le disjoncteur saute lorsqu'on allume le luminaire. Vérifiez les connexions électriques. 28 Ouvrez l'interrupteur ou le disjoncteur. Vérifiez ou remplacez l'interrupteur. Vérifiez les connexions électriques. Remplacer le contrôleur.
Cette page est intentionnellement laissée en blanc. HAMPTONBAY.COM Veuillez contacter le 1-855-HD-HAMPTON pour obtenir plus aide.
Questions, problèmes, pièces manquantes? Avant de retourner au magasin, appeler Hampton Bay Service à la clientèle 8:00 – 18:00, HNE, lundi – vendredi 1-855-HD-HAMPTON HAMPTONBAY.COM Conserver ce manuel pour un utilisation ultérieure.