Use and Care Manual

ManualsBrandsHampton Bay ManualsHanging LightsMayport Collection 3-Light Brushed-Nickel Hanging Large Pendant

CHANDELIER

Instruction Manual

Please read carefully and save these instructions, as you may need them at a later date.

SAFETY

WARNING: BE SURE THE ELECTRICITY TO THE WIRES YOU ARE WORKING ON IS SHUT OFF; EITHER THE FUSE

IS REMOVED OR THE CIRCUIT BREAKER IS TURNED OFF. TURNING THE POWER OFF USING THE LIGHT

SWITCH IS NOT SUFFICIENT TO PREVENT ELECTRICAL SHOCK.

NOTE: The important safeguards and instructions appearing in this manual are not meant to cover all possible conditions

or situations that may occur. It must be understood that common sense, caution, and care, are factors which cannot be

built into any product. These factors must be supplied by the person(s) installing this unit.

READ & SAVE THESE INSTRUCTIONS

CAUTION: Before assembling the lighting fixture, refer to the section titled Wiring Connections. If you feel you do not

have enough electrical wiring experience, either refer to a do-it–yourself wiring handbook or have your lighting fixture

installed by a qualified, licensed electrician.

UNPACK THE PACKAGE

Check the contents to be sure everything is included

Tools Needed: Slotted screwdriver, Adjustable wrench, Step ladder, Wire cutters, wiring supplies as required by electrical

code.

INSTALLATION & OPERATION INSTRUCTIONS

GENERAL

Before starting the installation, disconnect the power by turning off the circuit breaker or by removing the appropriate fuse

at the fuse box. Turning the power off using the light switch is not sufficient to prevent electrical shock.

All electrical connections must be in accordance with local and National Electrical Code (NEC) standards. If you are

unfamiliar with proper electrical wiring connections, obtain the services of a qualified electrician.

Remove the fixture and the mounting packages from the box and make sure that no parts are missing by referencing the

illustrations on the installation instructions.

Be sure to read these installation instructions and review the diagrams thoroughly before installation.

Summary of content (6 pages)

PAGE 1
CHANDELIER Instruction Manual Please read carefully and save these instructions, as you may need them at a later date. SAFETY WARNING: BE SURE THE ELECTRICITY TO THE WIRES YOU ARE WORKING ON IS SHUT OFF; EITHER THE FUSE IS REMOVED OR THE CIRCUIT BREAKER IS TURNED OFF. TURNING THE POWER OFF USING THE LIGHT SWITCH IS NOT SUFFICIENT TO PREVENT ELECTRICAL SHOCK. NOTE: The important safeguards and instructions appearing in this manual are not meant to cover all possible conditions or situations that may occur.
PAGE 2
Assembly and Installation 1. Thread Iron Bar (20) into center part (21) tightly. Then adjust steel wire (19) length, Use inner-Hex. Spanner (18) to thread Inner-Hex. Screw (17) into Ball (16) tightly. 2. Thread Tube (24) tightly onto threaded tube (22), then thread threaded tube (27) tightly onto tube (24). And then put Bent Tube Assembly (25) through threaded tube (27) and then tight with Hex. Nut (26). 3. Put Cup (28) through threaded tube (27) and then tight with Finial (29). 4.
PAGE 3
1. Junction box 2. Wire connector 3. Ground wire 4. Mounting plate 5. Ground screw 6. Fixture Wire 7. Hex nut 8. Washer 9. Threaded tube 10. Machine Screw 11. Canopy 12. Hanging loop 13. Ring 14. Chain 15. Canopy Loop 16. Ball 17. Inner-Hex. Screw 18. inner-Hex. spanner 19. Steel Wire 20. Iron Bar 21. Centre Part 22. Threaded tube 23. Glass Shade 24. Tube 25. Bent Tube Assembly 26. Hex. Nut 27. Threaded Tube 28. Cup 29. Finial 30. Bulb 31.
PAGE 4
ARAÑA Manual de instrucciones Lea cuidadosamente y guarde estas instrucciones ya que puede necesitarlas en el futuro. SEGURIDAD ADVERTENCIA: ASEGÚRESE DE QUE EL SUMINISTRO ELÉCTRICO DE LOS CABLES CON LOS QUE ESTÁ TRABAJANDO ESTÉ DESCONECTADO, QUE HAYA EXTRAÍDO EL FUSIBLE O QUE ESTÉ DESACTIVADO EL DISYUNTOR. DESCONECTAR EL SUMINISTRO ELÉCTRICO CON EL INTERRUPTOR DE LA LUZ NO ES SUFICIENTE PARA EVITAR DESCARGAS ELÉCTRICAS.
PAGE 5
Armado e instalación 1. Enrosque la barra de hierro (20) en la columna central (21) hasta que quede firmemente sujeta. Luego ajuste la longitud el alambre de acero (19) y use la llave hexagonal (18) para apretar firmemente el tornillo de cabeza hexagonal (17) en la bola (16). 2. Enrosque el tubo (24) en el tubo roscado (22), fije el tubo roscado (27) al tubo (24) y apriete hasta que queden firmemente sujetos.
PAGE 6
1. Caja de empalmes 2. Capuchón de empalme 3. Conductor de conexión a tierra 4. Placa de montaje 5. Tornillo de puesta a tierra 6. Cable del accesorio 7. Tuerca hexagonal 8. Arandela 9. Tubo roscado 10. Tornillo para metal 11. Rosetón 12. Argolla de suspensión 13. Aro 14. Cadena 15. Argolla del rosetón 16. Bola 17. Tornillo de cabeza hexagonal 18. Llave hexagonal 19. Alambre de acero 20. Barra de hierro 21. Columna central 22. Tubo roscado 23. Pantalla de vidrio 24. Tubo 25. Conjunto del grupo 26.