Item # 1004 999 345 Model # DS18854 USE AND CARE GUIDE 3 LIGHT SEMI FLUSH MOUNT Questions, problems, missing parts? Before returning to the store, call Design Solutions International Customer Service Mon-Fri 9:30 am to 3:00 pm EST 1-800-388-6141 ext. 216 For customer service support and the fastest response, please email us at CustomerSupport@DSILighting.
Table of Contents Table of Contents ........................................................... 2 Safety Information ......................................................... 2 Warranty ......................................................................... 2 Three (3) Year Warranty ................................................ ........ 2 What is Covered ....................................................................... 2 What is Not Covered ........................................................
Pre-Installation PLANNING INSTALLATION Read all instructions before installing. To avoid damaging this product, place it on a soft, non-abrasive surface, such as carpet or cardboard. IMPORTANT: Inspect the wire insulation for any cuts, abrasions, or exposed copper that may have occurred during shipping. If there is a defect in the wire, do not attempt installation. Please call Customer Service Team at 1-800-388-6141 ext 216.
Pre-Installation (continued) PACKAGE CONTENTS A B Part Description Quantity A Fixture body 1 B Cage 1 4
Installation 1 Installing the Cage □ 2 Installing the Crossbar Assembly □ Unfold support arms of the fixture body (A) to proper locations. (Refer to Arm Orientation) Remove mounting screw from the arm. Confirm that the holes on the cage (B) align with the mounting holes on the arm. Pass mounting screws through hole of the cage (B) and thread into the mounting holes on the arm. Hand-tighten until snug. □ □ Secure the crossbar (AA) to the outlet box (not included) with outlet box screws (BB).
Installation (continued) 4 □ □ 5 □ Making the electrical connections AA * Use Wire Connectors (supplied) to connect the wires. Ground Wire: 1. Wrap supply ground wire around green ground screw on mounting bracket, no less than 2 in. from the end of the wire. Tighten ground screw. 2. Connect fixture ground wire to supply ground wire with wire connector (CC). Supply Wire: 1. Connect the supply white wire to the white fixture supply wire with wire connector (CC). 2.
Care and Cleaning □ Do not use any cleaners with chemicals, solvents, or harsh abrasives. Use only a dry, soft cloth to dust or wipe carefully. To clean the fixture, disconnect power by turning off the circuit breaker or by removing the fuse at the fuse box, and use a dry or □ slightly dampened, clean cloth to wipe the exterior surface of the fixture. Troubleshooting Problem Possible Cause Solution The lights will not turn on. The bulb is burned out. The power is off. There is a faulty switch.
Questions, problems, missing parts? Before returning to the store, call Design Solutions International Customer Service Mon-Fri 9:30 am to 3:00 pm EST 1-800-388-6141 ext. 216 For customer service support and the fastest response, please email us at CustomerSupport@DSILighting.com Retain this manual for future use.
Artículo núm. 1004 999 345 Modelo DS18854 GUÍA DE USO Y MANTENIMIENTO SOPORTE DE MONTAJE SEMIEMPOTRADO DE 3 BOMBILLAS ¿Tiene alguna pregunta o algún problema? ¿Le faltan piezas? Antes de volver a la tienda, llame al Servicio de atención al cliente de Design Solutions International De lunes a viernes, de 9.30 a 15 h EST 1-800-388-6141 ext. 216 Para obtener ayuda de nuestro Servicio de atención al cliente y la respuesta más rápida, envíenos un correo electrónico a CustomerSupport@DSILighting.
Tabla de contenidos Tabla de contenidos....................................................... 2 Información de seguridad.............................................. 2 Garantía........................................................................... 2 Garantía de tres (3) años.............................................................. 2 ¿Qué cubre?................................................................................. 2 ¿Qué no cubre?.........................................................
Preinstalación PLANIFICACIÓN DE LA INSTALACIÓN Lea las instrucciones antes de comenzar la instalación. Para evitar dañar este producto, colóquelo sobre una superficie suave, no abrasiva, como una alfombra o un cartón. IMPORTANTE: Inspeccione el aislamiento del cable para detectar cualquier corte, abrasión o exposición del cobre que pueda haberse producido durante el envío. Si el cable tiene algún defecto, no intente realizar la instalación. Llame al 1-800-388-6141, ext.
Preinstalación (continuación) CONTENIDOS DEL PAQUETE A B Pieza Descripción Cantidad A Cuerpo de la lámpara 1 B Jaula 1 4
Instalación 1 Instalación de la jaula □ del soporte de barras 2 Instalación cruzadas □ Despliegue los brazos de soporte del cuerpo de la lámpara (A) como corresponde (consulte la orientación de los brazos). Desenrosque el tornillo de montaje de los brazos. Compruebe que los orificios de la jaula (B) queden alineados con los orificios de montaje de los brazos. Pase los tornillos de montaje por los orificios de la jaula (B) y enrósquelos en los orificios de montaje de cada brazo.
Instalación (continuación) 4 □ Realización de las conexiones eléctricas * Utilice los conectores de cables (incluidos) para conectar los cables. Cable de tierra: 1. Enrolle el cable de tierra de la alimentación alrededor del tornillo de toma a tierra verde en el soporte, no menos de 5 cm desde el extremo del cable. Apriete el tornillo de toma a tierra. 2. Conecte el cable de la toma de tierra de la lámpara con el cable de tierra de la alimentación con el conector de cables (CC).
Mantenimiento y limpieza □ No emplee productos de limpieza que contengan químicos, disolventes ni abrasivos. Utilice únicamente un paño seco para quitar el polvo o limpiar con cuidado. □ Para limpiar la lámpara, desconecte la alimentación apagando el disyuntor del circuito o retirando el fusible de la caja de fusibles y utilice un paño suave húmedo o ligeramente mojado para limpiar la superficie exterior de la lámpara. Reparación de averías Problema Posible causa Solución Las luces no se encenderán.
Conserve este manual para futuras consultas. ¿Tiene alguna pregunta o algún problema? ¿Le faltan piezas? Antes de volver a la tienda, llame al Servicio de atención al cliente de Design Solutions International De lunes a viernes, de 9.30 a 15 h EST 1-800-388-6141 ext. 216 Para obtener ayuda de nuestro Servicio de atención al cliente y la respuesta más rápida, envíenos un correo electrónico a CustomerSupport@DSILighting.com Conserve este manual para futuras consultas.