Installation Guide

ManualsBrandsHampton Bay ManualsLandscape LightingSolar Black LED Flicker Flame Path Light (12-Pack)

HAMPTONBAY.COM

Please contact 1-855-HD-HAMPTON for further assistance.

PACKAGE CONTENTS

PLANNING FOR A SUCCESSFUL ASSEMBLY

Read all instructions before assembly and installation.

Inspect each part for defects that may have occurred during shipping.

Keep your receipt and these instructions for proof of purchase.

CHOOSING THE RIGHT LOCATION

Install your solar light in a location with full, direct sunlight. Do not install in

shaded areas as these areas will not allow the batteries to fully charge and will

reduce the nighttime operating hours for your light. Ensure that the installation

location is away from other nighttime light sources such as street or porch lamps.

These light sources may prevent your solar light from automatically turning on.

Part Description Quantity

A Top cover 2

1.2V AA 1000mAh rechargeable battery

(pre-installed)

C Battery cover 2

D Housing 2

E Post 2

F Stake 2

HOW SOLAR WORKS

The solar light has a solar panel that converts sunlight into electricity. During the day, the converted electricity is stored in the rechargeable batteries. At night, the

solar light is powered by the batteries using the electricity stored during the day. The operating time depends on geographical location, daily weather conditions, and

season. For optimal performance during the evening, allow the batteries to charge for 6 to 7 hours in direct sunlight.

Assembly and Installation

NOTE: Do not use a hammer. If the ground is hard, use

water to soften or a trowel to loosen the soil.

Preparing for installation

Installing the solar path light

in the ground

□ Firmly slide the post (E) into the solar housing (D).

□ Attach the post (E) to the stake (F).

□ Push the assembly rmly into the ground.

1 2

Solar Flicker Flame Light

Use and Care Guide

Item #xxxx xxx xxx

Model #91999

□ Replace the top cover (A) on the housing (D) and twist to lock into place.

A B C D E F

□ FOR FIRST TIME USE: Twist and remove the housing (D) from the top cover (A).

□ Remove the pull tab from the battery compartment on the top cover (A).

□ Slide the switch to the ON or FLAME position depending on desired function.

Summary of content (4 pages)

PAGE 1
Use and Care Guide Solar Flicker Flame Light Item #xxxx xxx xxx Model #91999 PACKAGE CONTENTS A B C PLANNING FOR A SUCCESSFUL ASSEMBLY Read all instructions before assembly and installation. Inspect each part for defects that may have occurred during shipping. Keep your receipt and these instructions for proof of purchase. CHOOSING THE RIGHT LOCATION Install your solar light in a location with full, direct sunlight.
PAGE 2
Maintenance Replacing the battery CAUTION: When replacing the battery, use one (1) 1.2V AA 1000mAh rechargeable battery. C IMPORTANT: Dispose of the batteries in accordance with local, state, and federal regulations. A B NOTE: For best performance, replace with a rechargeable 1.2V AA 1000mAh battery every 3 years or when performance diminishes. □□ □□ □□ D Twist and remove the housing (D) from the top cover (A). Remove the battery cover (C). Replace the old battery with a fresh 1.
PAGE 3
Guía de uso y cuidado Luz parpadeante con forma de llama Artículo #xxxx xxx xxx Modelo #91999 CONTENIDO DEL PAQUETE A B C PLANIFICACIÓN DEL ENSAMBLAJE EXITOSO Leer todas las instrucciones antes de ensamblar e instalar. Inspeccionar cada una de las partes o piezas para ver si fueron afectadas durante el envío. Conservar el recibo y estas instrucciones como prueba de compra. ELECCIÓN DE LA UBICACIÓN ADECUADA Instalar la lámpara solar en un lugar donde reciba la luz del sol plena y directa.
PAGE 4
Mantenimiento Cómo reemplazar la batería CUIDADO: Al reemplazar la batería, usar una (1) recargable AA de 1.2 V y 1000 mAh. C IMPORTANTE: Desecha las baterías de acuerdo con las regulaciones locales, estatales y federales. A B NOTA: Para mejor rendimiento, reponer con una batería recargable AA de 1.2 V y 1000 mAh cada 3 años o cuando disminuya el rendimiento. □□ □□ □□ D Girar y quitar la carcasa (D) de la cubierta superior (A). Quitar la cubierta de la batería (C).