Caution : You must read this before you proceed Loveseat Picture Label A B C Picture Description Seat Right Armrest (Pre-Installed Levellers) Left Armrest (Pre-Installed Levellers) QTY 1 1 1
D Back Cushion Seat Cushion E Label 2 Description QTY ① Washer (M6) 7 ② Bolt (M6*35mm) 7 ③ Allen Key 1 ④ Bolt Cap 7 Before Beginning Assembly: Picture 2
Overview Back Cushion(D) Right Armrest(B) Seat Cushion(E) Left Armrest(C) Seat (A) Front Facing This Loveseat has multiple parts and may require up to 30 minutes to assemble. To give you an overview of the Loveseat parts, the above picture is to help you put the various parts into perspective. Please read through the instructions below to familiarise yourself with the parts and steps before assembly. Step 1 Open the carton, and place all parts on a clean, non-marring surface.
Step 2 Place the Right Armrest(B) face down. With the assistance of your adult partner, turn the Seat(A) and Left Armrest(C) over and place onto the Right Armrest(B). Attach the Seat(A) to the Right Armrest(C) using Bolts(②) and Washers(①) with Allen Key(③). Do not fully tighten the Bolts. Step 3 With the help of your adult partner, stand the Loveseat up. Place the Loveseat on a LEVEL SURFACE. Inspect it and make sure all parts are adequately connected.
Step 4 With the assistance of your adult partner, turn the Loveseat over and place the Bolt Caps(④) on all Bolts. Step 5 adjust height for balance adjust low for balance Stand the Loveseat upright. Adjust the Legs Pre-installed Levellers until the Loveseat is level with the ground.
Step 6 Place the Seat Cushion(E) on the Loveseat. Tie up the rope to the Seat(A). Step 7 Place the Back Cushion(D) on the Loveseat. Your Loveseat is ready for use. This Loveseat can only be used on a flat and level surface.
What is Proposition 65? Proposition 65 is a California law that requires warning labels on products that may contain one of more than 800-plus chemicals or ingredients that the California Office of Environmental Health Hazard Assessment (OEHHA) has deemed to cause cancer or other reproductive toxicity.
Caution : You must read this before you proceed Chair Label Picture Description QTY F Seat 1 B Right Armrest (Pre-Installed Levellers) 1 C Left Armrest (Pre-Installed Levellers) 1
D Back Cushion 1 E Seat Cushion 1 Description QTY ① Washer (M6) 7 ② Bolt (M6*35mm) 7 ③ Allen Key 1 ④ Bolt Cap 7 Label Before Beginning Assembly: Picture
Overview Left Armrest(C) Back Cushion (D) Right Armrest(B) Seat Cushion (E) Seat(F) Front Facing This Chair has multiple parts and may require up to 30 minutes to assemble. To give you an overview of the Table parts, the above picture is to help you put the various parts into perspective. Please read through the instructions below to familiarise yourself with the parts and steps before assembly. Step 1 Open the carton, and place all parts on a clean, non-marring surface.
Step 2 Place the Right Armrest(B) face down. With the assistance of your adult partner, turn the Seat(F) and Left Armrest(C) over and place onto the Right Armrest(B). Attach the Seat(F) to the Right Armrest(C) using Bolts(②) and Washers(①) with Allen Key(③). Do not fully tighten the Bolts. Step 3 With the help of your adult partner, stand the Chair up. Place the Chair on a LEVEL SURFACE. Inspect it and make sure all parts are adequately connected.
Step 4 With the assistance of your adult partner, turn the Chair over and place the Bolt Caps(④) on all Bolts. Step 5 adjust height for balance adjust low for balance Stand the Chair upright. Adjust the Legs Pre-installed Levellers until the Chair is level with the ground.
Step 6 Place the Seat Cushion(E) on the Chair. Tie up the rope to the Seat(F). Step 7 Place the Back Cushion(D) on the Chair. Your Chair is ready for use. This Chair can only be used on a flat and level surface.
What is Proposition 65? Proposition 65 is a California law that requires warning labels on products that may contain one of more than 800-plus chemicals or ingredients that the California Office of Environmental Health Hazard Assessment (OEHHA) has deemed to cause cancer or other reproductive toxicity.
Caution : You must read this before you proceed Table Label Description QTY G Table Top 1 H Leg (Pre-Installed Levellers) 2 Description QTY ① Washer (M6) 9 ② Bolt (M6*40mm) 9 Label Picture Picture
③ ④ 1 Allen Key Cap 9 Before Beginning Assembly: Overview Table Top(G) Leg(H) Leg(H) Front Facing This Table has multiple parts and may require up to 30 minutes to assemble. To give you an overview of the Table parts, the above picture is to help you put the various parts into perspective. Please read through the instructions below to familiarise yourself with the parts and steps before assembly.
Step 1 Open the carton, and place all parts on a clean, non-marring. Step 2 Place the Table Top(G) face down on the clean and soft surface. Place one Leg(H) over onto the Table Top(G). Attach the Leg(H) to the Table Top(G) using Bolts(②) and Washers(①) with Allen Key(③). repeat the same Repeat the same process for the other Leg. Tighten Bolts in a sequential manner.
Step 3 Use the Bolt Caps(④) to cover the Bolts. Step 4 adjust height for balance adjust low for balance Stand the Table upright. Adjust the Legs Pre-installed Levellers until the Table is level with the ground. Step 5 Your Table is ready for use. This Table can only be used on a flat and level surface.
What is Proposition 65? Proposition 65 is a California law that requires warning labels on products that may contain one of more than 800-plus chemicals or ingredients that the California Office of Environmental Health Hazard Assessment (OEHHA) has deemed to cause cancer or other reproductive toxicity.