Installation Guide
Operation
Installation
Part Description
Connector’s locking tab [preassembled to track head (A)]
B
A
Track head
TOOLS REQUIRED
PACKAGE CONTENTS
Pre-Installation
Pre-Installation
Quantity
1
1
Troubleshooting
Care and Cleaning
Ladder Gloves
□
removing the fuse at the fuse box.
□
□
CAUTION: Do not use chemical solvents or harsh
may occur.
Use a dry or slightly dampened, clean cloth (use clean water, never use a solvent) to wipe the
Problem Possible Cause Solution
The light bulb will not
illuminate.
The light bulb is burned
out.
Replace the light bulb.
The power is off.
Make sure the power supply is on.
There is a faulty wire
connection.
Check the wiring.
Contact a quali
ed and licensed
electrician if you are not comfortable
troubleshooting wiring problems.
There is a faulty switch.
Test or replace the switch.
There are crossed wires,
or the power wire is not
properly grounded.
Check the wire connections.
The fuse blows or the circuit
breaker trips when the light bulb
is illuminated.
Trim [preassembled to track head (A)]
C
1
Knob [preassembled to track head (A)]
D
2
Installing the bulb
Removing the track head from the track
Pull down on the track head connector’s locking tab (B), and twist until the track head (A) disengages.
□
□
Installation
B
A
A
AA
AA
C
C
Installing the track head to the track
Push the top portion of the track head (A) connector into the slot of the track section.
Pull down the connector’s locking tab (B).
Twist the ground side of the track head (A) connector toward the ground side of the track section
until the track head (A) connector snaps into place.
NOTE: The ground side of the track head (A) connector is the side with two metal tabs. The
ground side of the track section has an indented groove on the face and two internal copper
strips. The track head (A) can only be assembled if the ground sides of the track head (A)
connector and the track section are aligned.
□
Identify the ground side on the track head (A) connector and track section (sold separately).
□
□
□
□
Ground tab
Ground groove
Ground side of connector
Track (sold separately)
A
2
Removing the trim
1
3
Hardware not shown to actual size.
HARDWARE INCLUDED
NOTE:
x 1
Bulb
□
Remove the trim (C) from the track head (A).
Notice: When installing the trim, turn the trim clockwise
and make sure it is tight.
A
D
C
B
D
Adjusting the knob
□
2
1
B
A
A
Loosen the knob (D) on the side of the track head (A)
to adjust the lighting direction of the light. Tighten the
knob (D) when you reach the desired lighting direction.
Safety Information
IMPORTANT SAFETY INSTRUCTIONS
(Save These Instructions)
WHEN INSTALLING OR USING THIS TRACK SYSTEM, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE
FOLLOWED INCLUDING THE FOLLOWING:
NOTE
□
□
□
Do not install any part of this system less than
CAUTION: Keep the lamp away from
materials that may burn.
WARNING: Do not install this lighting
system in a damp or wet location.
□
□
All electrical connections must be in accordance
with local codes and the National Electrical Code.
If you are unfamiliar with methods of installing
electrical wiring, secure the services of a
Do not install any lamps closer than 6 in. from
any curtain or similar combustible material.
IMPORTANT: For use with Hampton Bay
EC series line voltage track systems only.
Turn off power and allow bulbs to cool down
before replacing.
CAUTION: To reduce the risk of a burn
during re-lamping, remove from the track
before re-lamping.
CAUTION
: Refer to the re-lamping label
recommended wattage.
Read all installation instructions. Save these
instructions and refer to them when additions to
: Make sure to install the shade ring
after installed the light bulb.
□
Pull the bulb socket from the track head (A) (for EC1588)
and insert the bulb (AA) into the socket.
Reattach the trim (C) to the bulb (AA). Reattach the trim (C)
to the track head (A).
Warranty
USE AND CARE GUIDE
LINEAR TRACK HEAD
□
5-YEAR LIMITED WARRANTY
or workmanship, the product must be returned, with a copy of the bill of sale as proof of purchase, to the
original place of purchase. The manufacturer will, at its option, repair, replace, or refund the purchase
becoming damaged due to misuse, accidental damage, improper handling and/or installation, and
exclusions or limitations on an implied warranty, so the above exclusions and limitations may not apply.
Contact the Customer Service Team at 1-855-HD-HAMPTON or visit www.hamptonbay.com.
7 a.m. - 6 p.m., EST, Monday - Friday, 9 a.m. - 6 p.m., EST Saturday
1-855-HD-HAMPTON
Questions, problems, missing parts? Before returning to store,
HAMPTONBAY. COM
Retain this manual for future use.
call Hampton Bay Customer Service
Model #EC1588BK-D, EC1588WH-D
EC8714BK-D, EC8714WH-D
Item #1004619418(805249), 1004618679(805229)
1004618678(805289), 1004612875(805269)
□
□
□
□
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
□ Please note that changes or modications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply
with thelimits for a Class B digital device, pursuant to
Part 15 of theFCC Rules. These limits are designed to
provide reasonableprotection against harmful
interference in a residentialinstallation. This equipment generates, uses and can radiateradio
frequency energy and, if not installed and used inaccordance with the instructions, may cause
harmfulinterference to radio communications. However, there is noguarantee that interference will
not occur in a particularinstallation. If this equipment does cause harmful interferenceto radio
ortelevision reception, which can be determined byturning the equipment off and on, the user is
encouraged to tryto correct the interference by one or more of the followingmeasures:
The manufacturer warrants this lighting xture against defects in materials and workmanship for a period
of ve years from the date of
purchase. If within this period the product is found to be defective in material
□
FCC responsible party name : Lumitic Corporation ./address: 2850 W Horizon Ridge Parkway #200
Henderson, Nevada United States NV89052 /Telephone number: 678-383-4085.
THANK YOU
We strive to continually create quality products designed to enhance your home. Visit us online to see our full line of
products available for your home improvement needs. Thank you for choosing Hampton Bay!