Model # 5LGZ1319-80 USE AND CARE GUIDE Toulon 10 ft x 8 ft Steel Pergola with Flat Roof Questions, problems, missing parts? Before returning to the store, call Hampton Bay Customer Service 8.00 a.m. - 7.00 p.m. EST, Monday - Friday, 9.00 a.m. - 6.00 p.m. EST, Saturday 1-855-HD-HAMPTON HAMPTONBAY.COM THANK YOU pergola. to continually create quality products designed to enhance your home. Visit us online to see our full line of products available for your home improvement needs.
Table of Contents Table of Contents........................................................2 Safety Information.......................................................2 Warranty ...................................................................... 2 One Year Frame and Fabric Limited Warranty............................ 2 What Is Covered .... .. ................................................................ 2 What Is Not Covered ..................................................................
Pre-Assembly PLANNING ASSEMBLY It will take two people about 35 minutes to complete the assembly process. A Philips screwdriver, a freestanding ladder and a rubber mallet are needed. HARDWARE INCLUDED NOTE: Hardware not shown to actual size. Part AA BB CC DD EE FF GG AA BB CC DD EE FF GG HH II JJ Description Bolt (M6x16) Bolt (M6x30) Bolt (M6x75) Bolt (12x29/M6x16) Self tapping screw (ST4.
Pre-Assembly PACKAGE CONTENTS A J K B L M C E D N O F F1 P G Q G1 R H I Part Quantity Part Corner post 2 B Corner post 2 J K Short side beam with rail Central beam with rail 2 1 C Post top ornament 4 Fixed pole 1 D L M A Description Post base ornament 4 E Post base 4 F F1 Rear side beam Front side beam 1 G Rear side beam 1 1 G1 Front side beam 1 H Short cross beam 2 I Short cross beam w/o rail 2 4/12 Description Quantity Fixed pole 1 Guide pole 4 4 N
Assembly 1 □ □ □ Assembling corner posts Slide post top ornament (C) followed by post base ornamment (D) up from the bottom on each corner post (A/B). Secure the post top ornament (C) to the top of the corner post with screws (EE) using a Philips Screwdriver. Attach the post base (E) to the bottom of corner post (A/B) with bolts (AA) using a Philips Screwdriver.
Assembly 2 Assembling long side beams □ Plug the rear side beam (G) into the rear side beam (F) and secure them with bolts (AA) using hex wrench (FF). (Fig.2.1) □ Plug the front side beam (G1) into the front side beam (F1) and secure them with bolts (AA) using hex wrench (FF). (Fig.2.2) □ Attach two pole receivers (Q) onto one of the front side beams (F1,G1) with bolts (AA) using hex wrench (FF). (FIg.2.
Assembly 3 □ □ Attaching short cross beams Attach one short cross beam (H) onto the top of two adjacent corner posts (A) and (B) with bolts (CC) using hex wrench (FF). (Fig.3.1) Repeat this for the other short cross beam.
Assembly 4 Attaching long side beams □ Attach the complete rear side beam (F/G) onto the top of corner posts with one bolt (CC) at each corner. □ Attach the complete rear side beam (F/G) to the short side beams (H) with two bolts (DD) at each outside corner using hex wrench (II). □ Follow the above proceedures for the complete front side beam (F1/G1).
Assembly 5 Assembling the roof frame (1) □ Attach the short side beams with rail (J) onto the top of the assembled long beams with bolts (CC) and bolts (AA) using hex wrench (FF).
Assembly 6 Assembling the roof frame (2) □ □ Attach the central beam (K) onto the top of the complete side beams (F_G, and F1_G1) with bolts (AA) using hex wrench (FF). Attach the short side beams (I) onto the the complete side beams (F_G, and F1_G1) with bolts (AA) using hex wrench (FF). IMPORTANT: Please put the ring (1) which is inside the rail of the beam (K) on the (F1_G1) side where the pole receivers (Q) are installed.
Assembly 8 □ □ □ □ □ □ □ □ Attaching the canopy fabric Secure the assembled poles (L) and (M) onto the long beams without the pole receivers (Q) with bolts (BB) using hex wrench (FF). (Fig.8.1) On both short sides of the pergola, tie the canopy to the rings inside the rails of the side cross beams (J) with the elastic band (2). (Fig.8.2) Secure poles (N) and (O) onto the rings inside the rails of the side cross beams (J) with bolts (AA) using hex wrench (FF). (Fig.8.
Assembly 9 Placement of the canopy pull □ For clean look, when the canopy is fully extened, please take down the canopy pull (R) and hook it on corner post (A). （Fig.9.1) □ When the canopy is fully folded, set the hook on side beam (G). (Fig.9.2) A (Fig. 9.1) R R G 12 /12 (Fig. 9.
