Installation Guide

Item # 100000000/ 100000000
Model # 564281010/ 564281020
HARDWARE INCLUDED
Part Description Quantity
AA Mounting Bracket 1
BB Mounting Screw (for Bracket) 2
CC Wire Connector 3
USE AND CARE GUIDE
11IN. FLUSHMOUNT WITH MOTION SENSOR
NOTE: Keep your receipt and these instructions for proof of purchase.
WARNING: RISK OF ELECTRIC SHOCK. Ensure the electricity to the wires you are working on is shut off. Either remove the
fuse or turn off the circuit breaker before removing an existing light fixture or installing the new one.
If you are unfamiliar with electrical installations, we recommend you contact a qualified electrician to do the installation.
INSTALLATION
Select a suitable location that can support the weight of the fixture. Determine the method for mounting the fixture before
drilling, based on the type of ceiling.
1. Pass the hot and neutral (black and white) wires from the electrical outlet box through the middle hole of the mounting
bracket (AA).
Align the mounting bracket (AA) using the mounting screws (BB) and tighten securely to the electrical box.
2. Connect the hot and neutral (black and white) wires from the J-box to the same color wires from the fixture body (A).
Connect the grounding wire from the J-box to the green wire from fixture base (A). Cover the wire connections using the
wire connectors (CC). Make sure to fasten them well.
3. Cover the wire connectors (CC) with electrical tape for a more secure connection.
4. Position the wires back inside the electrical box.
5. Align the side slots on the fixture body (A) with the mounting bracket (AA) and fix the fixture body (A) securely by carefully
rotating in clockwise the side slots inside the mounting bracket (AA).
6. Restore power at the electrical panel. Turn on the light switch to activate the fixture.
MULTIPLE SETTING FEATURES INCLUDE: Dusk-to-Dawn, Motion and Disable
Use slide switch on back of fixture to make your selection prior to installation.
• Dusk to Dawn (DTD): Allows the fixture to come on when darkness is sensed at 100% lumen outuput.
• Motion: Allows the fixture to come on at dusk and then drop down to 30% lumen output until motion is sensed and then the lumen
output boosts up to 100% and holds that for 5 minutes until motion is no longer sensed.
• Disable: Allows the fixture to be switch controlled only. In this mode, by toggling the wall switch within 3 seconds, the end user can
set the light level to 30% or 100%.
• NOTE: The detected range is 15ft.
PACKAGE CONTENTS
Part Description Quantity
A
Fixture Body 1
A
AA BB CC
STEP 1. STEP 2. STEP 3.
BB
AA
AA
CC
A
Side slot
Hold time options of
motion sensor:
Color temperature
(CCT) options:
Questions, problems, missing parts? Before returning to the store, call Hampton Bay Customer Service
8 a.m. - 7 p.m., EST, Monday – Friday, 9 a.m. – 6 p.m., EST, Saturday
1-855-HD-HAMPTON | Hamptonbay.com
Retain this manual for future use.
CARE AND CLEANING
CAUTION: Before attempting to clean the tube and luminaire/light xture, disconnect the power to the xture by turning the
breaker off or removing the fuse from the fuse box. Clean with a soft, dry cloth. Do not use cleaners with chemicals, solvents, or
harsh abrasives. Do not use liquid cleaner on the LEDs, LED driver, or wiring.
TROUBLESHOOTING
Minor problems often can be fixed without the help of an electrician.
WARNING: Before doing any work on the fixture, disconnect power to the light fixture.
WARNING: Carefully read and understand the information given in this manual before beginning the assembly and installation.
Failure to do so could lead to electric shock, re, or other injuries which could be hazardous or even fatal. • Ensure the electricity to
the wires you are working on is shut off. Either remove the fuse or turn off the circuit breaker. • To reduce the possibility of serious
injury, always take the proper precautions and unplug the xture before moving or cleaning. • Risk of re or electric shock.
NOTICE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving
antenna, increase the separation between the equipment and the receiver, connect the equipment into an outlet on a circuit different from
that to which the receiver is connected, and consult the dealer or an experienced radio/TV technician for help. Changes or modications not
expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
WARRANTY
WHAT IS COVERED
The manufacturer warrants this lighting fixture to be free from defects in materials and workmanship for a period of five (5) years from
date of purchase. This warranty applies only to the original consumer purchaser and only to products used in normal use and service. If
this product is found to be defective, the manufacturer’s only obligation, and your exclusive remedy, is the repair or replacement of the
product at the manufacturer’s discretion, provided that the product has not been damaged through misuse, abuse, accident, modifications,
alterations, neglect, or mishandling.
WHAT IS NOT COVERED
This warranty shall not apply to any product that is found to have been improperly installed, set-up, or used in anyway not in accordance
with the instructions supplied with the product. This warranty shall not apply to a failure of the product as a result of an accident, misuse,
abuse, negligence, alteration, faulty installation, or any other failure not relating to faulty material or workmanship. This warranty shall not
apply to the nish on any portion of the product, such as surface and/or weathering, as this is considered normal wear and tear.
The manufacturer does not warrant and specifically disclaims any warranty, whether express or implied, of fitness for a particular purpose,
other than the warranty contained herein. The manufacturer specifically disclaims any liability and shall not be liable for any consequential
or incidental loss or damage, including but not limited to any labor / expense costs involved in the replacement or repair of said product.
Contact the Customer Service Team at 1-855-HD-HAMPTON or visit www.HAMPTONBAY.com.
Problem Possible Cause Solution
The fixture will not light.
The power is off. Ensure the power supply is on.
The circuit breaker is off. Ensure the circuit breaker is in the on position.
There is a bad connection. Check to ensure proper wire connections are made.
Contact a qualified electrician.
There is a defective switch. Contact a qualified electrician.
The fuse blows or the circuit
breaker trips when the light is
turned on.
The wires are crossed or the power
wire is grounding out.
Check the wire connections.
Contact a qualified electrician or call Hampton Bay
customer service 1-855-HD-HAMPTON.
ADJUSTING THE COLOR TEMPERATURE OF THE LIGHT
This LED light fixture allows you to customize the color temperature of
the light using three settings: soft white, bright white, or daylight.
1. Choose your favorite correlated color temperature (CCT) from
three options: 2700K warm white, 3000K soft white,
3500K neutral white, 4000K bright white, or 5000K daylight.
2. Move the toggle switch on the fxture body (A) to make your
selection before inserting into bracket or ceiling.
NOTE: The factory setting for the correlated color temperature
(CCT) is 2700K.
DTD/ Motion/ Disable
2700K 3000K 3500K 4000K 5000K