Use and Care Manual

ManualsBrandsHampton Bay ManualsDeck LightingSolar 2-Toned Black Integrated LED Deck Rail Light with Brushed Nickel Top (2-Pack)

Please contact 1-830-249-1200 for further assistance



USE AND CARE GUIDE

SOLAR DECK LIGHT

TOOLS REQUIRED HARDWARE INCLUDED

Phillips

screwdriver

Electric drill

AA - Wood screw x 2 BB - Plastic anchor x 2

Installation

Wood post/fence mounting

Wall mounting

□ To mount the solar light to a wood post or fence, measure and mark

on the wood surface the locations of both mounting screws 2 in. on-

center.

□ Insert the mounting screws (AA)into the wood post or fence at the

marked locations, leaving about 1/4 in. of the screws (AA) sticking

out of the wood surface.

□ Align and place the two mounting holes on the back plate of the

solar light over the mounting screws (AA).

IMPORTANT

: Prior to use, pull out the top cap (A) from the lamp

housing (B). Then,

remove the battery isolator tag (C) from the battery

compartment. Re

place the top cap back on the lamp housing and

allow it to charge for a full sunny day.

IMPORTANT: Ensure the mounting location for your solar light allows

the solar panel to receive direct sunlight. Do not locate the product in

shaded areas as this will significantly reduce performance.

NOTE: The solar light is equipped with a photosensor that turns the

unit on at dusk and off at dawn. Ambient light can affect the operation

of the photosensor.

□ To mount the solar light to a concrete wall, measure and mark on the

wall locations of both mounting screws 2 in. on-center.

□ Drill two holes on the wall at the marked locations.

□ Insert the plastic anchors (BB) into the holes. Insert the mounting

screws (AA)into the anchors (BB), leaving about 1/4 in. of the screws

(AA) sticking out of the wall surface.

□ Align and place the two mounting holes on the back plate of the solar

light over the mounting screws (AA).

IIMPORTANT

: Prior to use, pull out the top cap (A) from the lamp

housing (B). Then,

remove the battery isolator tag (C) from the battery

compartment. Replace the top cap back

on the lamp housing and

allow it to charge for a full sunny day.

IMPORTANT: Ensure the mounting location for your solar light allows

the solar panel to receive direct sunlight. Do not locate the product in

shaded areas as this will significantly reduce performance.

NOTE: The solar light is equipped with a photosensor that turns the

unit on at dusk and off at dawn. Ambient light can affect the operation

of the photosensor.

Safety Information

WARNING: Your solar light may not function in temperatures below -

4ºF (-20ºC) or above 140ºF (60ºC).

CAUTION: Use a rechargeable battery only. Recycle or dispose of

batteries properly.

CAUTION: Do not open, short circuit, or mutilate batteries as injury

may occur.

Summary of content (4 pages)

PAGE 1
 USE AND CARE GUIDE SOLAR DECK LIGHT TOOLS REQUIRED HARDWARE INCLUDED Phillips screwdriver AA - Wood screw x 2 Electric drill BB - Plastic anchor x 2 Installation 1 □ □ □ Wood post/fence mounting To mount the solar light to a wood post or fence, measure and mark on the wood surface the locations of both mounting screws 2 in. oncenter. Insert the mounting screws (AA)into the wood post or fence at the marked locations, leaving about 1/4 in. of the screws (AA) sticking out of the wood surface.
PAGE 2
Maintenance Replacing the battery IMPORTANT: Dispose of the battery in accordance with local, state, and federal regulations. IMPORTANT: When storing any solar product for an extended period of time, remove the batteries. Storing any solar product without regular recharge or removal of batteries could cause permanent damage to the rechargeable batteries. NOTE: Use one AA-size, 500mAh, 1.2V nickel-metal hydride rechargeable battery.
PAGE 3
Guía de uso y cuidado LUZ SOLAR PARA TERRAZA HERRAMIENTAS REQUERIDAS HERRAJE INCLUIDO Destornillador Phillips AA - Tornillo para madera x 2 Taladro eléctrico BB - Anclaje plástico x 2 Instalación 1 □ □ □ Montaje en postes de madera/cercas Para montar la luz solar a un poste de madera o cerca, mida y marque las ubicaciones en la superficie de madera de los dos tornillos de montaje a 2 pulgadas del centro.
PAGE 4
Mantenimiento Cómo reemplazar la pila IMPORTANTE: Deseche la pila cumpliendo con los reglamentos locales, estatales y federales. IMPORTANTE: Al almacenar cualquier producto solar durante un periodo prolongado de tiempo, retire las pilas. Almacenar un producto solar sin una recarga frecuente o la extracción de las baterías podría causar daños permanentes a las baterías recargables. NOTA: Use unapila recargable de tamaño AA, 500 mAh, 1.2 V de níquel-metal hidruro.