Item # 1002 448 209 Model # 17678 USE AND CARE GUIDE 1-LIGHT WALL SCONCE Questions, problems, missing parts? Before returning to the store, call Design Solution International Customer Service Mon-Fri 9:30 am to 3:00 pm EST 1-800-388-6141 ext 216
Table of Contents Table of Contents ........................................................... 2 Safety Information ......................................................... 2 Warranty ......................................................................... 2 Five (5) Year Warranty ............................................................. 2 What is Covered ........................................................................ 2 What is Not Covered ....................................................
Pre-Installation PLANNING INSTALLATION Read all instructions before installing. To avoid damaging this product, place it on a soft, non-abrasive surface, such as carpet or cardboard. IMPORTANT: Inspect the wire insulation for any cuts, abrasions, or exposed copper that may have occurred during shipping. If there is a defect in the wire, do not attempt installation. Please call Customer Service Team at 1-800-388-6141 ext 216.
Pre-Installation (continued) PACKAGE CONTENTS A B C Part Description Quantity A Socket ring 1 (Pre-assembled to the socket of fixture body (C)) B C Glass shade Fixture body 1 1 4
Installation □ Loosen the hex nuts (DD) on the support screws (long) (BB) and adjust the support screws (long) (BB) so that they extend long enough to protrude through the canopy of the fixture body (C), then secure the support screws (long) (BB) in place using the hex nuts (DD). □ Fasten the mounting bracket (AA) onto the outlet box using two outlet box screws (short) (CC). BB Unscrew the two cap nuts (GG) from the support screws (long) (BB).
Installation (continued) 4 Installing the fixture body to the outlet box Place the canopy of the fixture body (C) over the outlet box, and ensure the heads of the support screws (long) (BB) come through the holes of back of the fixture body (C). □ Tighten the cap nuts (GG) onto the protruding support screws (long) (BB) on the mounting bracket (AA) until the fixture body (C) is held firmly against the wall. □ There are two installation options to choose from.
Care and Cleaning □ Do not use any cleaners with chemicals, solvents, or harsh abrasives. Use only a dry, soft cloth to dust or wipe carefully. □ To clean the fixture, disconnect power by turning off the circuit breaker or by removing the fuse at the fuse box, and use a dry or slightly dampened, clean cloth to wipe the exterior surface of the fixture. Troubleshooting Problem Possible Cause Solution The lights will not turn on. The bulb is burned out. The power is off. There is a faulty switch.
Service Parts MODEL: 17678 BB AA EE DD FF CC GG A Part Description AA Mounting bracket Support screw (long) BB CC DD EE FF B (Pre-assembled to mounting bracket (AA)) Outlet box screw (short) Hex nut (Pre-assembled to support screw (BB)) Green ground screw (Pre-assembled to mountiong bracket (AA)) GG Wire connector Cap nut A Socket ring (Pre-assembled to support screw (BB)) (Pre-assembled to the socket of fixture body (C)) B C Glass shade Fixture body C 8
Questions, problems, missing parts? Before returning to the store, call Design Solution International Customer Service Mon-Fri 9:30 am to 3:00 pm EST 1-800-388-6141 ext 216 Retain this manual for future use.
Artículo núm. 1002 448 209 Modelo núm. 17678 GUÍA DE USO Y MANTENIMIENTO LÁMPARA DE PARED DE UNA BOMBILLA ¿Tiene alguna pregunta o algún problema? ¿Le faltan piezas? Antes de volver a la tienda, llame al Servicio de atención al cliente de Design Solution International De lunes a viernes, de 9.30 a 15 h EST 1-800-388-6141 ext.
Tabla de contenidos Tabla de contenidos........................................................ 2 Información de seguridad.............................................. 2 Garantía........................................................................... 2 Garantía de cinco (5) años.......................................................... 2 ¿Qué cubre?............................................................................... 2 ¿Qué no cubre?.............................................................
Preinstalación PLANIFICACIÓN DE LA INSTALACIÓN Lea las instrucciones antes de comenzar la instalación. Para evitar dañar este producto, colóquelo sobre una superficie suave, no abrasiva, como una alfombra o un cartón. IMPORTANTE: Inspeccione el aislamiento del cable para detectar cualquier corte, abrasión o exposición del cobre que pueda haberse producido durante el envío. Si el cable tiene algún defecto, no intente realice la instalación. Llame al 1-800-388-6141, ext.
Preinstalación (continuación) CONTENIDOS DEL PAQUETE A B C Pieza A Descripción Cantidad Anilla del casquillo 1 (preinstalada en el casquillo del cuerpo de la lámpara [C]) B C Pantalla de cristal Cuerpo de la lámpara 1 1 4
Instalación □ Afloje las tuercas hexagonales (DD) en los tornillos de soporte (largos) (BB) y ajuste los tornillos de soporte (largos) (BB) para que sobresalgan lo justo por la base del cuerpo de la lámpara (C). A continuación, apriete bien los tornillos de soporte (largos) (BB) con la ayuda de las tuercas hexagonales (DD). □ Fije el soporte (AA) en la caja de dos tornillos de la caja de distribución (cortos) (CC). BB Desenrosque las dos tuercas ciegas (GG) de los tornillos de soporte (largos) (BB).
Instalación (continuación) 4 Instalación del cuerpo de la lámpara a la caja de distribución Coloque la base del cuerpo de la lámpara (C) sobre la caja de distribución y asegúrese de que las cabezas de los tornillos de soporte (largos) (BB) salgan por los orificios de la parte trasera del cuerpo de la lámpara (C). □ Apriete las tuercas ciegas (GG) a los tornillos de soporte (largos) (BB) que sobresalen del soporte (AA) hasta que el cuerpo de la lámpara (C) esté fijado con firmeza contra la pared.
Mantenimiento y limpieza □ No emplee productos de limpieza que contengan químicos, disolventes ni abrasivos. Utilice únicamente un paño seco para quitar el polvo o limpiar con cuidado. □ Para limpiar la lámpara, desconecte la alimentación apagando el disyuntor del circuito o retirando el fusible de la caja de fusibles y utilice un paño suave húmedo o ligeramente mojado para limpiar la superficie exterior de la lámpara. Reparación de averías Problema Posible causa Solución Las luces no se encenderán.
Piezas de repuesto MODELO: 17678 BB AA EE DD FF CC GG A Pieza AA BB CC DD Descripción Soporte Tornillo de soporte (largo) B (preinstalado en el soporte [AA]) Tornillo de la caja de distribución (corto) Tuerca hexagonal (preinstalada para sujetar el tornillo [BB]) EE Tornillo de toma a tierra verde FF GG Conector de cable Tuerca ciega A Anilla del casquillo (preinstalado en el soporte [AA]) (preinstalada para sujetar el tornillo [BB]) (preinstalada en el casquillo del cuerpo de la lámpar
¿Tiene alguna pregunta o algún problema? ¿Le faltan piezas? Antes de volver a la tienda, llame al Servicio de atención al cliente de Design Solution International De lunes a viernes, de 9.30 a 15 h EST 1-800-388-6141 ext. 216 Conserve este manual para futuras consultas.