Installation Guide

ManualsBrandsHampton Bay ManualsLightingCreme Brulee 1-Light Kendallwood Mini Pendant

INSTALLATION INSTRUCTIONS

For Item#17085 (06/01/2009)

READ AND SAVE THESE INSTRUCTIONS

WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.

Fig. 1

Fig. 2

FIXTURE

WIRES

Black or

Smooth

USE

WIRES

Black

(Hot)

FIXTURE

WIRES

White or

Ribbed

USE

WIRES

White

(Neutral)

FIXTURE

WIRES

Bare

Copper

(Ground)

USE

WIRES

Green

(Ground)

LA-1488E/S

HANGING THE FIXTURE (Fig. 1)

1. Shut off power at the fuse box or circuit breaker

box. If necessary, remove old fixture and all

mounting hardware from wall junction box.

2. Carefully unpack your new fixture and lay out all the

parts on a clear area. Take care not to lose any

small parts necessary for installation.

3. Determine length desired and thread Bars (F) to

Canopy (D) and Nipple (G).

4. Attach the Circular Strap (A) to the Outlet box using

Junction Box Screws (B) from the outlet box. The

side of the Circular Strap with “GND” marked on it

and two convex points must face out.

5. Thread two Studs (C) about 1/4” into the pre-drilled

holes in the Circular Strap (A) spaced the same

distance apart as the holes in the canopy.

CONNECTING THE WIRES (Fig. 2)

t this point, connect the electrical wire as shown in

(Fig.2), making sure that all wire connectors are

secured. If your outlet has a ground wire (green or

bare copper), connect the fixture’s Ground Wire to

it. Otherwise, connect the fixture Ground Wire

directly to the Circular Strap using the Green Screw

provided.

7. Tuck the wire connections neatly into the ceiling

unction box and then raise the Canopy (D) all the

way to the ceiling. Thread Studs (C) into canopy,

and secure with Knurled Knobs (E).

8. Install Glass Shade (I) over Socket (H) and secure

with Screw Shell (J) using the Spanner (K).

9. Install the light bulb in accordance with the fixture’s

specifications. (DO NOT EXCEED THE MAXIMUM

WATTAGE RATING!)

Your installation is now complete. Return power to the

junction box and test the fixture.

Note: Illustration (Fig. 1) on this manual is for

installation purposes only. It may or may not be

identical to the fixture purchased.

In the event that you should have any installation question o

are missing parts, please contact Customer Service.

Customer service may be reached weekdays a

1-800-527-0998 between the hours of 8:00am and 5:00pm

PST (Pacific Standard Time).

Summary of content (2 pages)

PAGE 1
INSTALLATION INSTRUCTIONS For Item#17085 (06/01/2009) READ AND SAVE THESE INSTRUCTIONS WARNING! S H U T P O W E R O F F AT F U S E O R C I R C U I T B R E A K E R . HANGING THE FIXTURE (Fig. 1) 1. Shut off power at the fuse box or circuit breaker box. If necessary, remove old fixture and all mounting hardware from wall junction box. 2. Carefully unpack your new fixture and lay out all the parts on a clear area. Take care not to lose any small parts necessary for installation. 3.
PAGE 2
INSTRUCCIONES PARA LA INSTALACION Para Modelo#17085 (06/01/2009) AGUARDE ESTAS INSTRUCCIONES ADVERTENCIA! CORTE LA CORRIENTE DESDE EL FUSIBLE O EL INTERRUPTOR CENTRAL. PREPARACION (Fig. 1) 1. Corte la corriente en la caja de fusibles o en el circuito principal. Si fuera necesario, saque la lampara vieja y todo el montaje de la caja de union de la pared. 2. Desempaque cuidadosamente la nueva lampara y coloque todas las partes en una superficie despejada.