User's Instructions

ManualsBrandsHaltian Products ManualsElectronicsSensor device with wireless connection

PD2 USER INSTRUCTIONS

1. INTENDED USE OF PD2

PD2 is used for measurements of several physical quantities and resulting data is

sent wirelessly to a Wirepas protocol mesh network. The device has sensors for

temperature, humidity, air pressure, ambient light, magnetism and acceleration. It

also includes an LED for indication purposes. Typically PD2 is used together with

MTXH Thingsee Gateway in use cases where the measurements are performed in

several locations and this data is wirelessly collected and sent via 2G cellular

connection to a data server / cloud.

2. GENERAL

Place two AAA batteries (recommended model Varta Industrial) inside the device,

the correct direction is shown on the PWB. Plus sign indicates the positive node of

the battery.

Summary of content (10 pages)

PAGE 1
PD2 USER INSTRUCTIONS 1. INTENDED USE OF PD2 PD2 is used for measurements of several physical quantities and resulting data is sent wirelessly to a Wirepas protocol mesh network. The device has sensors for temperature, humidity, air pressure, ambient light, magnetism and acceleration. It also includes an LED for indication purposes.
PAGE 2
Snap the B cover in place. The device starts making measurements with all the sensors. Measurements are made once a minute (default, can be changed by configuration). The device starts seeking any other nearby devices having the same preprogrammed Wirepas network ID as the device itself. If it finds any, it connects to this Wirepas network and starts sending measurement results from all the sensors to the network once a minute (default, can be changed by configuration).
PAGE 3
. INSTALLATION GUIDELINES The device B cover has a double-sided tape which can be used for attachment; remove the cover tape and attach the device to the desired position for measurement. The surface for attachment needs to be flat and clean. Press the device from both sides for 5 seconds to make sure that the tape is correctly attached to the surface.
PAGE 4
The device operates with fresh Varta Industrial batteries typically for more than 2 years (this time depends heavily on the configuration used for measurement and reporting intervals). If there is a need to change the batteries, spread the side of the A cover gently as shown in the picture below. Be careful while opening the cover that locking snaps don’t break. Remove the B cover, remove the batteries and place new batteries as described earlier.
PAGE 5
The tool can be ordered from Haltian Products Oy.
PAGE 6
The device can also be ordered with batteries pre-installed. In this case just pull out the tape disconnecting batteries in order to power on the device. 4. PRECAUTIONS - PD2 is intended for indoor use only and shall not be exposed to rain. The operating temperature range for the device is -20…+50 °C. - Remove the batteries from the PD2 device if you are taking it inside an aeroplane (unless you have the pre-installed pull-out tape still in place).
PAGE 7
- Do not try to charge primary batteries. - Do not open or disassemble batteries. - Batteries should be stored in a dry place and at room temperature. Avoid large temperature changes and direct sunlight. At higher temperature the electrical performance of the batteries may be reduced. - Keep batteries away from children. 5. CERTIFICATION INFORMATION EU DECLARATION OF CONFORMITY Hereby, Haltian Products Oy declares that the radio equipment type PD2 is in compliance with Directive 2014/53/EU.
PAGE 8
FCC REQUIREMENTS FOR OPERATION IN THE UNITED STATES FCC Information for the User This product does not contain any user serviceable components and is to be used with approved, internal antennas only. Any product changes of modifications will invalidate all applicable regulatory certifications and approvals. FCC Guidelines for human Exposure This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
PAGE 9
installation. This equipment uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
PAGE 10
NOTE IMPORTANTE: Déclaration d'exposition aux radiations: Cet équipement est conforme aux limites d'exposition aux rayonnements ISED établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec une distance minimale de 10 mm entre le radiateur et votre corps.