Installation Guide

ManualsBrandsHalo ManualsLightingALS 48-Watt Equivalent Integrated LED Gray Dusk to Dawn Area Light, 4000K

Questions?/Des questions?/¿Preguntas? 1-800-334-6871 ConsumerProducts@cooperlighting.com

PACKAGING CONTENTS/CONTENU DE L’EMBALLAGE/CONTENIDO DEL PAQUETE

Instruction Manual / Manuel d’instructions/ Instrucciones

equipment generates uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or tele-

vision reception, which can be determined by turning the equipment off an on, the user is

encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

WARNING: FCC Regulations state that any unauthorized changes or

modications to this equipment not expressly approved by the manufacturer could

void the user’s authorization to operate this equipment.

Supplier's Declaration of Conformity

47 CFR § 2.1077 Compliance Information

Unique Identier: Standard Area Light

Responsible Party – U.S. Contact Information

Cooper Lighting Solutions

1121 Highway 74 S

Peachtree City, GA

30269

www.cooperindustries.com/content/public/en/lighting.html

Telephone Number: 1-800-942-0763

FCC Compliance Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following

two conditions: (1) This device may not cause harmful interference, and (2) this device

must accept any interference received, including interference that may cause undesired

operation.

ITEMS REQUIRED

(Purchase separately)

• Phillips screwdriver

• Adjustable wrench or ratchet wrench with 8mm and 10mm socket

• Drill with 3/16 in. drill bit

• 1/2 in. diameter conduit (if applicable, length depends on application)

• 1/2 in. watertight conduit connectors (if applicable)

IMPORTANT SAFETY INSTRUCTIONS

When using product, basic precautions should always be followed, including the following:

• Heed all warnings, including below warnings AND those included on product.

• Save these instructions and warnings.

• For outdoor use only.

• cULus LISTED for wet location.

• Disassembling your xture will void the warranty.

• Your xture is prewired and preassembled for easy installation.

• Read and follow these instructions.

• Risk of re/electric shock. If not qualied, consult an electrician.

• Disconnect power at fuse or circuit breaker before installing or servicing.

• Edges may cut. Handle with care.

CAUTION

• Connect xture to a 120V, 60 Hz power source. Any other connection voids the

warranty.

• Fixture should be installed by persons with experience in household wiring or

by a qualied electrician. The electrical system, and the method of electrically

connecting the xture to it, must be in accordance with the National Electrical

Code and local building codes.

• Upside down installation can result in overheating or accumulation of water in

xture. Install right side up.

FCC DECLARATION OF CONFORMITY

This device complies with part 15 of the FCC Rules. Operation is subject to the following 2

conditions: (1) This device may not cause harmful interference, and (2) this device must accept

any interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

ENGLISH

WARNING

ALS7A40GY

ALS10A40GY

E. WIRE CONNECTORS

CONDUIT CONNECTOR

4 3

ALS 3 Pin PCR Instruction

Sheets Figures

1.705 LB

47.186 IN3

L MOD:

E0439882

7/10/2020

ALS 3 Pin PCR

Instruction Sheets

Figures

TOLERANCE GENERAL

DIMENSIONS THAT AFFECT

SAFE HANDLING OR

OPERATION

1229.155 IN2

DEV/ZINT NO:

1 OF

ANGLES

1.0

ALL

PRODUCT MUST CONFORM TO ROHS

COOPER LIGHTING SOLUTIONS - CONFIDENTIAL AND PROPRIETARY

NOTICE TO PERSONS RECEIVING THIS DOCUMENT AND/OR TECHNICAL INFORMATION

THIS DOCUMENT, INCLUDING THE DRAWING AND INFORMATION CONTAINED THEREON, IS

CONFIDENTIAL AND IS THE EXCLUSIVE PROPERTY OF EATON, AND IS MERELY ON LOAN

AND SUBJECT TO RECALL BY COOPER LIGHTING SOLUTIONS AT ANY TIME. BY TAKING POSSESSION

OF THIS DOCUMENT, THE RECIPIENT ACKNOWLEDGES AND AGREES THAT THIS DOCUMENT CANNOT

BE USED IN ANY MANNER ADVERSE TO THE INTERESTS OF COOPER LIGHTING SOLUTIONS,AND THAT

NO PORTION OF THIS DOCUMENT MAY BE COPIED OR OTHERWISE REPRODUCED WITHOUT THE

PRIOR WRITTEN CONSENT OF COOPER LIGHTING SOLUTIONS. IN THE CASE OF CONFLICTING

CONTRACTUAL PROVISIONS, THIS NOTICE SHALL GOVERN THE STATUS OF THIS DOCUMENT.

Cooper Lighting SolutionsTemplate Rev -

IP LEVEL:

REVISIONS

REV. DESCRIPTION DATE CHANGE_NUMBER BY APPROVED

A. LIGHT FIXTURE

FIGURE 1

CONDUIT

B. ACCESS COVER

I. PHOTOCONTROL SENSOR

F. POLE MOUNTING CLAMP/ACCESS COVER MOUNTING SCREWS

C. MOUNTING SCREWS

D. POLE MOUNTING CLAMP

G. DROP REFRACTOR

2.125

1.375

2.750

USE FOR PACKAGING ARTWORK

H. DROP REFRACTOR MOUNTING SCREWS

FIGURE 2

THIRD ANGLE PROJECTION

MATERIAL:

METRIC (MM)

ENGLISH (IN)

.XX

.XXX

.XX

.XXX

DIMENSIONS ARE IN INCHES

DIMENSIONS IN [ ] ARE IN MM

ELECTRONIC CAD DRAWING. DO

NOT REVISE MANUALLY.

SURFACE AREA:

DO NOT SCALE DRAWING

DRWN:

DATE

APPROVALS

0.040

0.020

0.010

0.5

0.25

x.x

DENOTES CRITICAL

DIMENSIONS AND

GAUGE CHECK POINTS

DENOTES FIRST PIECE

AND IN-PROCESS

INSPECTION

DENOTES FIRST

PIECE

INSPECTION ONLY

PART NUMBER

TITLE:

SIZE:

DWG NO:

REV:

SHEET

VOL:

WT:

SCALE:

FINISH:

APPR:

CHKD:

A. Light xture

Appareil d’éclairage

Accesorio

C. Mounting Screws (3)

Vis de montage (3)

Tornillos de montaje (3)

F. Pole Mounting Clamp/

Access Cover Mounting Screws (2)

Collier de xation pour poteau/vis de

xation du couvercle d'accés (2)

Tornillos de montaje de la abrazadera de

montaje del poste/tapa de acceso (2)

G. Drop Refractor

Réfracteur de chute

Refractor de caida

I. Photocontrol Sensor

Photoélectrique sensor

Sensor de fotoeléctrica

B. Access Cover

Couverture de l'accés

Cubierta acceso

D. Pole Mounting Clamp

Pince de montage pour

poteau

Pinza de montaje en poste

H. Drop Refractor Mounting Screws (2)

Vis de montage du réfracteur de chute (2)

Tornillos de montaje del refractor de caida (2)

E. Wire Connectors (3)

Serre-l (3)

Conectores de cable (3)

CONDUITCONNECTOR

CONDUIT

E. WIRE CONNECTORS

H. DROP REFRACTOR MOUNTING SCREWS

4 3

ALP Instruction Sheets

Figures

2.113 LB

58.477 IN3

L MOD:

E0439882

7/10/2020

ALP Instruction Sheets

Figures

TOLERANCE GENERAL

DIMENSIONS THAT AFFECT

SAFE HANDLING OR

OPERATION

1125.655 IN2