Quick Installation Guide GPON ONT HALNY HL-4GQV
HALNy HL-4GQV Quick Installation Guide Safety Guidance 1.1 Safety Check Before installing the device, you must check the following items. 1.1.1 Electric Safety l Ensure that there are no inflammable, conductive or moist objects around.
HALNy HL-4GQV Quick Installation Guide l Power off the idle device, l Keep the ventilation hole clean and prevent any object from dropping into the device through it. Otherwise, it may cause short circuit and further cause device damage or fire.
HALNy HL-4GQV Quick Installation Guide 2.2 Front, rear and side Panel The description of the front, rear and side panel of the GPON ONU as follows. 2.2.1 Front Panel Fig. 1 - Front Panel LED Color PWR Green PON Green LOS Red WAN Green LAN1-4 Green 2.4G 5G Green Green TEL1-2 Green WPS Green Status On Description The power works normally. Powered off or the power supply is abnormal.
HALNy HL-4GQV Quick Installation Guide PON LED Status Instruction PON LOS Description Off Off The ONT is disabled by the OLT Flash Off The ONT is registering to the OLT On Off The ONT has already registered to OLT Off Flash The fiber is not connected properly Table 2.PON LED Status Instruction 2.2.2 Rear Panel 2.2.2.1. Fig 2. Rear Panel ONU Rear Panel Description: Interface / Function Button LAN1-4 Power Ethernet interface, for connecting to a computer or an Ethernet interface of a switch.
HALNy HL-4GQV Quick Installation Guide Interface / Function Button ON/OFF Turn on/off the power supply. TEL1-2 RJ-11 Telephone Port Table 3.
HALNy HL-4GQV Quick Installation Guide 2.2.3 Side Panel Fig 3 Side Panel ONT Bottom Panel Description: Button WLAN Function Press and hold for 5 seconds to disable/enable Wi-Fi WPS Press and hold for 5 seconds to activate WPS pairing RST Press and hold for 5 seconds to Reset configuration to the factory default settings. 3 ONU Installation The chapter describes the required installation operations before you use the device for the first time. 3.
HALNy HL-4GQV Quick Installation Guide &Note: The ONU applies to installation at home or in the corridor. Because installation and cabling in the corridor are relatively complex, let the professional engineers deploy according to the actual situation. This manual describes the procedure for installing the device at home, and is for reference only. 3.2 Installation Preparations The Ethernet interface of your computer connects to the Ethernet interface of the ONU.
HALNy HL-4GQV Quick Installation Guide Caution: l When a fiber is not in use, ensure to cover the optical interface of the ONU and the dust cap of the optical fiber. Prevent grease, dust pollution or water immersion, which may lead to unavailable fiber and optical interface of the device. l If fibers need to be fixed or bended during cabling, do not fasten the fibers too tight. Avoid fiber extrusion, which may lead to increase of fiber material or unavailable fiber. 3.2.
HALNy HL-4GQV Quick Installation Guide 4 Troubleshooting Symptom The POWER indicator is not on The PON indicator is not on The LOS indicator is not on Solution = Check whether the power connection is correct, = Check whether the power adapter matches the device. = Check whether the SN of ONU matches OLT, = Check whether the optical attenuation is in the normal range. = Check whether the optical fiber cable is properly inserted, = Check whether the optical fiber connector is clean.
HALNy HL-4GQV Quick Installation Guide 5 Technical Specification Main Technical Specifications Standard Rate GPON Standard ITU-T G.984, TR156/TR255 Uplink 1.25Gbps Downlink 2.5Gbps Optical interface Single Mode 4 LAN ports Interface RJ-45 10/100/1000Mbps MDI/MDIX adaption 2 POTS ports RJ-11 FXS WiFi 2.4Ghz 802.11n (2T2R MIMO) 300Mbps WiFi 5Ghz 802.
HALNy HL-4GQV Quick Installation Guide Additional information: Declaration of Conformity (CE) This device has been tested and found to comply with the stated standards which are required by the Council Directive of 2014/30/EU. The device complies with this CE Declaration when the installation is done in accordance with the instruction and documentation. The importer don’t take responsibility for any issues caused by improper use of the device.
HALNy HL-4GQV Quick Installation Guide FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
HALNy HL-4GQV Quick Installation Guide uncontrolled enviroment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. Recycling This product bears the selective sorting symbol for Waste electrical and electronic equipment (WEEE). This means that this product must be handled according to European directive 2012/19/EU in order to be recycled or dismantled.