HARDTOP GAZEBO WITH NETTING If you have any questions about the outdoor gazebo, please feel free to contact us. Customer Service Email: Service@alaulm.com 1220Gazebo24 IMPORTANT PLEASE READ BEFORE YOU COMMENCE ASSEMBLY Follow the guidelines in this user guide to ensure correct assembly and care for this product.
SPECIFICATIONS 42.9 inch 122.0 inch 81.5 inch 135.4 inch 138.6 inch 122.0 inch 81.5 inch 231.5 inch 42.9 inch 144.5 inch 138.6 inch 240.
Catalog Specifications......................................................................................................... 01 Notice And Warning ........................................................................................... 03 Exploded Views ........................................................................................................ 05 First Part .............................................................................................................. 06 Second Part .......
NOTICE Note: The gazebo needs to be installed in cooperation with five people. The following tools are not included and needed for assembly: Pistol Drill Screw Driver Tape Measure 2 m Adjustable Ladder Hammer 5 people Warning 1. A 5 personal assembly is required for this gazebo. 2. Please take appropriate actions as heavy rain, wind and snow can damage the gazebo. If necessary please disassemble and store it for later use. 3.
PLEASE RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE. Dear Customer, Thank you for shopping with us! When you receive the product, please make sure that all the parts are intact. Then please browse the entire installation manual before assembling. If any problem occurs unsatisfactorily as follows: A.The outer box is damaged B.The product is damaged / bent / cracked while you open the box C.The parts / accessories / assembly tools are missing D.The product is hard to assemble E.
EXPLODED VIEWS First Part Second Part Third Part Fourth Part Fifth Part 05
S P2 P1 R8 R8 P1 P2 S S P7 P7 S S 06 P7 R9 P7 S S P7 P7 S S P7 P7 S S P7 R10 P7 S S P7 P7 S S P2 P1 R8 R8 P1 P2 S FIRST PART
X1 07 Y3 M1 Y3 K L1 K L9 L9 X5 M11 P M12 X6 K1 K1 D8 X7 L10 L10 X8 M13 K2 D9 K2 M13 X8 L10 L10 X7 D8 K1 K1 P X6 M12 L9 L9 M11 X5 K L1 K Y3 M1 Y3 X1 SECOND PART
08 Q2 S S S S S S S Q1 S S S S Q10 Q10 S S Q10 Q10 S S Q10 Q10 S S Q10 Q10 S S Q10 Q10 S S Q7 Q7 S S Q6 Q5 R4 R4 S Q4 Q3 S S R5 R5 Q1 Q6 Q4 Q4 Q1 S Q5 S Q2 Q3 Q5 Q10 Q10 S Q6 Q7 Q7 S Q7 R4 R4 Q6 S Q7 Q3 Q4 S Q7 R5 S Q7 Q5 Q3 R5 Q2 Q1 S S S S S S S Q2 THIRD PART
09 Y3 M8 Y2 M7 Y3 G2 G2 L6 J1 L6 G1 M14 L5 L5 G1 M15 L12 D1 L12 L11 D D L11 Y2 J1 J1 Y2 L13 L13 M16 D5 D6 L13 L13 M17 J5 J3 J2 J5 J4 D6 D5 M17 L13 L13 L13 L13 M16 Y2 J1 J1 Y2 L11 D1 L12 D D L11 L12 M15 L5 L5 M14 G1 J1 G1 L6 L6 G2 G2 Y3 M7 Y2 M8 Y3 FOURTH PART
10 C B Y5 Y4 A H2 T2 H1 E4 Y6 Y8 B C H1 E3 T2 E8 T5 A Y5 Y4 Y6 H2 Y8 C1 B1 E9 T5 E10 T6 A1 Y9 T6 Y8 Y8 Y6 Y6 E10 C1 B1 T6 Y9 A1 E9 T5 T6 C B H2 Y5 A Y4 Y8 H1 Y6 E3 T2 T5 Y6 Y8 E8 C B H1 E4 T2 A H2 Y5 Y4 FIFTH PART
Parts List (Box A) A J2 J3 M14 M15 Column Large center beam 1 Large center beam 2 Big Top Long Side Stopper Tube 1 Big Top Long Side Stopper Tube 2 4 PCS 1 PC 1 PC 2 PCS 2 PCS R4 R8 R5 T2 T5 Cover plate on big top diagonal beam Large top diagonal beam under cover Small top diagonal beam cover Short side mosquito net tube Long side mosquito net tube 4 PCS 4 PCS 4 PCS 4 PCS 4 PCS T6 Long side center mosquito net tube 4 PCS Parts List (Box B) E3 E4 Center Column Short side be
Parts List (Box C) D1 D5 D6 D8 D9 Large top frame short tube Big Top Frame Long Tube 1 Big Top Frame Long Tube 2 Small Top Connector Small Top Connectors Plugin 2 PCS 2 PCS 2 PCS 2 PCS 1 PC J1 G1 G2 R9 R10 Center crossbar Upper part of the big top diagonal beam Lower part of the big top diagonal beam Roof Plate Roof plate with baffle 6 PCS 4 PCS 4 PCS 1 PC 1 PC Y8 Beam Inserts 6 PCS Parts List (Box D) B C B1 Spike cover Floorboards Center spike cover 4 PCS 4 PCS 2 PCS
Parts List (Box D) K1 K2 L1 L5 L6 Small top center beam Small top intermediate center beam Small top short side girder Small beams on the upper edge of the big top Small beams on the lower edge of the big top 4 PCS 2 PCS 2 PCS 4 PCS 4 PCS L9 M1 L10 L11 Small top long side girder Small beam in the center of the long side of the small top Small beam in the Small top long side center of the long side upper edge beam of the large top 4 PCS 4 PCS M11 M12 Small top long side downstops 1
Parts List (Box E) P2 P1 P7 Q1 Q2 Small top short side left flap Small top short side right flap Small top long side center flap piece Small cover piece to the left of the big top Small cover piece to the right of the big top 4 PCS 4 PCS 12 PCS 4 PCS 4 PCS Q3 Q4 Q5 X1 Q6 Medium-sized cover Medium-sized cover Large diagonal cover Large diagonal cover piece on the left side piece on the right piece on the left side piece on the right of the big top side of the big top of the big top side o
Hardware List(Box F) AA CC BB Cross big flat he ad self-tapping M4*16 20 PCS Cross Outer Hexagon Bolt M6*20 Flat washer M6 Hexagon nut M6 Flat head hexagon socket head bolts M6*45 4 PCS 8 PCS 4 PCS 40 PCS HH LL JJ Cross Outer Hexagon Bolt M6*15 Mosquito net ring Cross Outer Hexagon Bolt M6*55 M6 Hole Plug 134 PCS 152 PCS 4 PCS 8 PCS 426 PCS KK EE Cross Outer Hexagon Bolt M6*35 GG FF DD QQ PP Z2 Z1 Cross Outer Hexagon Bolt M6*45 Round head nail Φ8*180 Cross Outer Hexagon B
STEP 1 Step 1:Attach the column(A) to the floorboards(C) with screws(FF). Then slip the spike cover(B) into the column(A).
STEP 2 Step 2:Insert the beam inserts(Y8) into short side beam 1 (E3) and short side beam 2(E4) with the holes aligned and fasten with screws(FF). NOTE:Look at the picture to determine the location of the screw holes.
STEP 3 Step 3:Insert the beam insert (Y8) into the long side center beam (E10) and the two long side crossbeams (E8 and E9), aligning the holes, noting the orientation, and tighten with screws (FF). NOTE:Look at the picture to determine the location of the screw holes.
STEP 4 T2 4x Step 4:Install the short side mosquito net tube(T2) on the short side beam(E3 and E4) with screws(FF), slide the mosquito net ring(HH) into the slots of the mosquito net tube(T2) from the side, each mosquito net tube(T2) has 14 mosquito net rings(HH). Fix the beam center stopper(Y6) to the joint of the two short side beam(E3 and E4) with screws(AA)and fix the center beam lower connector(Y2) to the short side beam(E3 and E4) with screws(FF).
STEP 5 Step 5:Install the long side mosquito net tube(T5) on the long side crossbeam(E8 and E9) with screws(FF), Install the long side center mosquito net tube(T6) on the long side center beam(E10) with screws (FF),slide the mosquito net ring(HH) into the slots of the mosquito net tube(T5) from the side, each mosquito net tube(T5) has 24 mosquito net rings(HH).
STEP 6 Step 6:Use screws(EE) to connect and fix the connected short side beam(E3 and E4) and column(A), and then use screws(GG) to connect the diagonal brace(H1 and H2) with the short side beam(E3 and E4) and column(A).Use screws (FF) to connect the columns(A) and the connector under inclined beam(Y4) . NOTE:Review the pictures to determine the location of the screw holes and the orientation of the parts.
STEP 7 Step 7:Attach the center column(A1) to the center floorboards(C1) with screws(FF). Then slip the center spike cover(B1) into the center column(A1). Secure the already attached long side center beams(E10) to the center columns(A1) with screws (EE). NOTE:Review the pictures to determine the location of the screw holes and the orientation of the parts.
STEP 8 Step 8:Use screws(EE) to connect and fix the connected long side crossbeam(E8 and E9) and column(A), and then use screws(GG) to connect the diagonal brace(H1 and H2) with the side beam(E3,E4,E8 and E9) and column(A). NOTE:Review the pictures to determine the location of the screw holes and the orientation of the parts.
STEP 9 Step 9:Fasten the beam corner stopper(Y5) to the corners of the side beam(E3,E4,E8 and E9) with screws(AA). NOTE:Review the pictures to determine the location of the screw holes and the orientation of the parts.
STEP 10 Step 10:The two large center beams (J2 and J3) are fixed with screws (FF) and connected in the center by a large center beam insert 1(J4).The large center beam lower connectors(Y9) are then fastened to the underside of the two large center beams(J2 and J3) with screws(FF). NOTE:Review the pictures to determine the location of the screw holes and the orientation of the parts.
Step 11:Fasten the two large center beams (J2 and J3) to STEP 11 the long side center beam(E10) with screws(FF). NOTE:Review the pictures to determine the location of the screw holes and the orientation of the parts.
Step 12:Connect the two large top frame long tube(D5 and STEP 12 D6) together with screws(FF).Connect the large top frame D 4x short tube(D1) and the big top frame long tube(D5 and D6) with the connector for the upper part of the big top diagonal beam pieces(D) and then lock them with screws(FF). NOTE:Review the pictures to determine the location of the screw holes and the orientation of the parts.
STEP 13 Step 13:Connect the top frame(D1,D5 and D6) to the base frame with center crossbar(J1) and the two large center beams (J2 and J3), place the center crossbar(J1) on top of the center beam lower connector(Y2) and fix it with the screws(GG). NOTE:Review the pictures to determine the location of the screw holes and the orientation of the parts.
STEP 14 Step 14:Insert the lower part of the big top diagonal beam (G2) into the upper part of the big top diagonal beam(G1) and secure with screws(GG). NOTE:Review the pictures to determine the location of the screw holes and the orientation of the parts.
STEP 15 Step 15:Adjust the diagonal beam in the right direction, connect the top frame to the bottom section and secure with screws(CC and JJ). NOTE:Review the pictures to determine the location of the screw holes and the orientation of the parts.
STEP 16 Step 16:Attach the two small top connectors(D8) together with the small top connectors plugin(D9) and then tighten with the screws(GG). NOTE:Review the pictures to determine the location of the screw holes and the orientation of the parts.
STEP 17 Step 17:Screw the small top sloping beam(K) and the small top connector(D8) to the top frame, and then install it with screws(GG). NOTE:Review the pictures to determine the location of the screw holes and the orientation of the parts.
STEP 18 Step 18:Screw the small top center beam(K1),the small top intermediate center beam(K2) and the small top connector (D8) to the top frame, and then install it with screws(GG). NOTE:Review the pictures to determine the location of the screw holes and the orientation of the parts.
Step 19:Attach the large top frame side mosquito net STEP 19 cover plate(X1,X5,X6,X7 and X8) in place between the big top and the small top with screws(FF). NOTE:Review the pictures to determine the location of the screw holes and the orientation of the parts.
STEP 20 Step 20:Place the small top side girder(L1,L9 and L10) in the center of the small top diagonal beams,and then attach the small top side girder(L1,L9 and L10) to the small top with screws(FF). NOTE:Review the pictures to determine the location of the screw holes and the orientation of the parts.
Step 21:Place the small top side down stop tube(M1,M11, STEP 21 M12 and M13) M1 2x in the center of the small top diagonal beams,and then attach the small top side down stop tube (M1,M11,M12 and M13) to the small top with screws(FF). Fix the small top intermediate center beam(K2) to the small beam in center of the long side of the small top(M13) with the screws(FF). NOTE:Review the pictures to determine the location of the screw holes and the orientation of the parts.
STEP 22 Step 22:Attach the small top cover piece(P1,P2 and P7) to the small top frame with the screws(FF) in the position shown in the illustration. NOTE:Review the pictures to determine the location of the screw holes and the orientation of the parts.
Step 23:Attach the layer(S) to the small top cover piece(P1, STEP 23 P2, and P7) with the screws(FF) in the position shown in the illustration. NOTE:Review the pictures to determine the location of the screw holes and the orientation of the parts.
STEP 24 Step 24:Attach the roof plate(R9),the roof plate with baffle (R10) and hook up(P) to the small top connector(D8) with screws(KK), attach the small top diagonal beam cover(R8) to the four ridges of the small top with screws(QQ), then attach the inclined beam stopper(Y3) to the four edge corners of the small top with screws(FF). NOTE:Review the pictures to determine the location of the screw holes and the orientation of the parts.
STEP 25 Step 25:Secure the small beams on the edge of the big top (L5,L6,L11 and L12) to the large top frame with screws (FF). NOTE:Review the pictures to determine the location of the screw holes and the orientation of the parts.
STEP 26 L13 Step 26:Place the small beam in the center of the long side of the small top(L13) on the large center beam(J1,J2 and J3) of the big top and secure it with screws(FF) on both sides.Secure the small beam(L13) to the large center beam (J2 and J3) with screws(GG). NOTE:Review the pictures to determine the location of the screw holes and the orientation of the parts.
STEP 27 Step 27:Fasten the large center beam insert 2(J5) to the large center beam(J2 and J3) with screws(FF). Secure the big top downtube(M7,M8,M14,M15,M16 and M17) to the large top frame with screws (FF). NOTE:Review the pictures to determine the location of the screw holes and the orientation of the parts.
STEP 28 Step 28:Secure the left and right side large top cover tabs (Q1,Q2,Q3,Q4,Q5 and Q6)to the big top frame with screws (FF) in the locations shown in the mounting illustrations. NOTE:Review the pictures to determine the location of the screw holes and the orientation of the parts.
STEP 29 Step 29:Secure the front and rear side large top cover tabs (Q1,Q2,Q3,Q4,Q5,Q6,Q7 and Q10)to the big top frame with screws(FF) in the locations shown in the mounting illustrations. NOTE:Review the pictures to determine the location of the screw holes and the orientation of the parts.
Step 30:Attach the layer(S) to the large top cover piece STEP 30 with the screws(FF) in the position shown in the illustration, then attach the inclined beam stopper(Y3) to the four edge corners of the large top with screws(FF). NOTE:Review the pictures to determine the location of the screw holes and the orientation of the parts.
Step 31:Secure the bottom half of the large top diagonal STEP 31 beam cover plate(R5) to the diagonal beam with screws (QQ), then insert the top half of the large top diagonal beam cover plate(R4) over the bottom half of the large top diagonal beam cover plate(R5) by aligning it with the holes in the small uprights,and then secured with screws(QQ). NOTE:Review the pictures to determine the location of the screw holes and the orientation of the parts.
STEP 32 Step 32:Hang the mosquito net(U3) on the mosquito net ring(HH) on the inside of the mosquito net tube(T2,T5 and T6).Attach the four corners of the sticky tape to the post. NOTE:Mosquito net with 12 hanging loops on the long side and 7 loops on the short side.
Step 33:Hang the surrounding cloth(V3) on the mosquito STEP 33 net ring(HH) on the outside of the mosquito net tube(T2,T5 and T6).Attach the four corners of the sticky tape to the post. NOTE:Mosquito net with 12 hanging loops on the long side and 7 loops on the short side.
STEP 34 Step 34:Secure the post to the ground with ground nails (PP) and expansion screws(UU). NOTE:Review the pictures to determine the location of the screw holes and the orientation of the parts.
www.alaulm.