Installation Instructions

ManualsBrandsHallmark Marketing ManualsElectronics2.4GHz Module

1.1 List of applicable FCC rules/RSS:

The module complies with FCC Part 15.249 / RSS-210 Issue 10

1.2 Summarize the specific operational use conditions:

The module has been certified for Portable applications. This transmitter must not be collocated or

operating in conjunction with any other antenna or transmitter

The manual provides guidance to the host manufacturer will be included in the documentation that will

be provided to the OEM.

The OEM integrators, host manufacturers are responsible for ensuring that the end-user has no manual

or instructions to remove or install module.

Important notes to third party user, host manufacturer for transceiver module:

The transceiver Module complies with Part15 of the FCC rules and regulations. Compliance with the

labeling requirements, FCC notices and antenna usage guidelines is required. To fulfill FCC Certification,

the third-party user must comply with the following regulations:

1. The third-party user must ensure that the text on the external label provided with this device is placed

on the outside of the final product. Contains FCC ID: SQ9RTX7310 / IC: 5768B- RTX7310. The enclosed

device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)

this device may not cause harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.

2. The transceiver Module may only be used with the onboard PCB antenna (internal, integral antenna)

that have been tested and approved for use with this module.

3. The transmitter is certified as a module, it may be integrated or used inside another device (host). No

further approval is required when the module is used in accordance with the FCC grant conditions, and

any limitations or usage conditions required by the manufacturer's instructions. Modifications not

approved by grantee could void the user's authority to operate the equipment.

4. This device and its antenna must not be co-located or operating in conjunction with any other

antenna or transmitter.

5. Third party users, host manufacturer must test final product to comply with unintentional radiators

before declaring compliance of their final product to Part 15 of the FCC Rules.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired

operation.

Summary of content (7 pages)

PAGE 1
.1 List of applicable FCC rules/RSS: The module complies with FCC Part 15.249 / RSS-210 Issue 10 1.2 Summarize the specific operational use conditions: The module has been certified for Portable applications. This transmitter must not be collocated or operating in conjunction with any other antenna or transmitter The manual provides guidance to the host manufacturer will be included in the documentation that will be provided to the OEM.
PAGE 2
FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
PAGE 3
The host manufacturer is responsible for additional testing to verify compliance as a composite system. When testing the host device for compliance with the Part 15 Subpart B requirements, the host manufacturer is required to show compliance with the Part 15 Subpart B while the transmitter module(s) are installed and operating. The modules should be transmitting and the evaluation should confirm that the module’s intentional emissions are compliant (i.e.
PAGE 4
The host product Labeling Requirements: NOTICE: The OEM system integrator, host manufacturer must make sure that FCC labeling requirements are met. This includes a clearly visible exterior label on the outside of the final product housing that displays the contents shown in below: This device contains FCC ID: SQ9RTX7310 This device contains IC: 5768B-RTX7310 This device complies with Part 15 of the FCC Rules.
PAGE 5
This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
PAGE 6
添信（香港）有限公司 Team Honour (HK) Ltd. Teamhonour RTX7310 2.4GHz module User Manual How to place the module on main PCB If the product uses modules on-board design, the location of modules should be considered, to reduces the effect on module antenna performance from the main PCB. it is suggested to extend the module antenna area out of the main PCB and make the module as close to the edge of main PCB as possible.
PAGE 7
添信（香港）有限公司 Teamhonour Team Honour (HK) Ltd. How to test the module Set the output voltage of power supply to 5v, and connect the output plug to the test jig power input terminal. - + Power supply 5v Test key Schematic diagram of power supply and test Jig Set the distance between the test Jig and the receiver. During the test, the transmitting power is 5dBm, usually the distance is about 8m.