User manual- HaiweiTech- General Last updated: 7/ 1/ 2021
Contents Preface………………………………………………………………..1 Part Ⅰ: Connection illustrated………………………………………..4 Part Ⅱ: Configure network…………………………………………...4 Part Ⅲ: Encoder Functions ………………………………………….6 Part Ⅳ: Operation Guidance…………………………………………13 Part Ⅴ: LiveX………………………………………………...………16 Part Ⅵ: FAQ…………………………………………………………..17 Part Ⅶ: contact us …………………………………………………….
Preface In order to learn more about the product information, technical operation of HD encoder more efficiently, convenient and fast maintenance for engineers and professionals, HaiweiTech keeps updating its instruction manual if renewed.
Part Ⅰ: Connection illustrated Part Ⅱ: Configure network DHCP suggested for new customer or will use it in different networks, so network configuration can be ignored if parameter of the stream configured.
Part Ⅱ: Configure Network 1- Get current IP Windows+ R → cmd →Enter: ipconfig →Get the IPv4 Add 2- Enter Ethernet 3- Enter Properties 4- Enter IPV4 and fill the IPv4 address you get from the 1st step and its subnet mask and default IP gateway Fill the correct dns, 8.8.8.8 suggested for global streaming 5- Enter Advanced 6- Add an available IP address @192.168.1.xxx and save all configurations.
1- Open a Browser and enter Default IP address of the encoder 192.168.1.168 Enter an available IP Enter your gateway 8.8.8.8 recommended Note: Reboot required while net configured * DNS In general, we recommend 8.8.8.8 for the DNS1, changing a DNS will probably helps if the stream does not start to decode.
Part Ⅲ: Encoder Functions 1- States Access address – Show the RTSP/ RTMP pull/ HTTP/ UDP/ RTP address Video/ Audio parameters – Show the information of the inputting signal Hardware status– If the encoder working normally, the data will keeps going Preview– VLC based preview for P-P encoder, HTML5 based for general encoder 2- Network 1)- general encoder- Once the network configured, to change the IP address of the encoder to your local IP gateway required
2)- 4G/ WIFI encoder- Once the network configured, to change the IP address of the encoder to your local IP gateway required; If need to use WiFi, different IP gateway to encoder IP required; for 4G, enable STA MODE.
To choose H.264/ H.265 for streaming To choose the input source Set your channel name for to recognize the encoder Rotate the video To choose the display resolution from 4:3 or 16:9 To choose VBR/ CBR To change the GOP size To change the output resolution To change the output video bitrate higher level higher bit fluctuation Alternatives: H.265 main, H.
To choose SRT caller or listener SRT encryption Set up the server IP Set up SRT port SRT server cache 2nd stream - The parameters are same to the 1st stream, to see more details please check the previous page - The 2nd stream can use at most 1280*720 for HDMI/ SDI encoder, the resolution will be lower than main stream - 1st and 2nd stream can be used at same time
To choose the input source, SDI/ HDMI, Line In To modify the audio bitrate To choose audio channel, alternative: Left/ right/ stereo AAC/ MP3 LC/ HE Enable/ disable Resample RTSP over AAC/ G.
Image optimization To adjust the video quality based on the video sources RTMP-HLS To enable RTMP pull and HLS protocol, for general encoder, HTML5 preview will be available once the HLS enabled.
System To reboot, reset, change admin password, check the firmware version and upgrade the firmware.
Part Ⅳ: Operation Guidance 1) HTTP-RTSP- RTMP pull- HLS Copy the address and open it with VLC- streaming- network- fill the URL ( Except RTMP push) Such as HTTP： WEB management→ HDMI Main→ Enable HTTP/ RTPS→ Apply→ Status( find the URL) → VLC→ fill the URL→ Done
2) Unicast- Multicast- RTP For those three protocol, fill in the IP address required (multicast can be by default) Then copy the address and open it with VLC- streaming- network- fill the URL Such as HTTP： WEB management→ HDMI Main→ Enable HTTP/ RTPS→ Apply→ Status( find the URL) → VLC→ fill the URL→ Done To get RTMP pull- HLS stream address on, UI- Extended- RTMP-HLS
3) RTMP (Push/ pull)- HLS URL mode Copy the CORRECT RTMP address from the server or platform and directly paste it on the RTMP filed, then “Enable” the RTMP function. IP mode Copy the CORRECT RTMP address from the server or platform, separately input it like following image, then “Enable” the RTMP function.
Part Ⅴ: LiveX APP—LiveX, control the encoder and record the video at anywhere, any network, any device. Android/ IOS: download it on its apple/ Google play store Video about LiveX on YouTube: https://www.youtube.
No Question 1 How to connect encoder? 2 How to access to encoder? Solution Connect encoder with computer directly via net cable. Set up one constant IP including IP: 192.168.1.1**, then access to 192.168.1.168 on PC browser. Copy the streaming URL to VLC - Media- Open network stream- paste, enjoy it. 3 How to watch the TS stream from the encoder? 1 Enable RTSP on the user interface, and watch it on VLC with same step to last question. 2.
Part Ⅵ: Contact us HaiweiTech E: hansen@hw-iptv.
