User Manual

ManualsBrandsHaiweiTech ManualsElectronicsH.265 H.264 4K Video Audio Decoder IP Camera Decoder RTMP SRT M3U8 UDP to HDMI CVBS BNC Decoder for Advertisement Display, Decoding Video Encoder, Decoding IP Camera

FHD Decoders

The S9110D Series based decoders were

designed for H.264/ H.265 IP (RTMP/ RTSP/ RTP/

HTTP/ HLS/ UDP/ SRT), MPEG1, MPEG2, MPEG4, SL

hyperlink (P-P), VP8/ VP9/ AVS/ AVS+ decoding

New FPGA architecture based high performance

decoder enables vividly high quality video output

over an SDI connector (SD/ HD/ 3G)

Input

Output

H.264/ 265 IP (RTMP/ RTSP/ RTP/ HTTP/ HLS/ UDP/

SRT),MPEG1, MPEG2, MPEG4, SL hyperlink (p-p), SRT,

VP8/ VP9/ AVS/ AVS+ (compatible with 4K stream)

SDI: 1080P@ 60/50/ 24, 1080I@ 60/50,

720P@ 60/50, 576I/ P@ 50, 480I/ P @60

Audio: HDMI/ 3.5mm output in MP3

Accessibilities

Power- 12V 2A For S9110D

Consumption: 2.8W for S9110D

Working Environment

-20℃+ 60℃

Humidity

＜90%, non-condensation

Weight

S9110D (Portable) - 0.3kg

Multi-view

1/ 4* TCP/ IP/ SRT Input, MPTS supported

深圳海威视讯技术有限公司/ HaiweiTech

Shenzhen headquarters (Factory): 6th floor, Block B, Huafeng financial port, Xin‘An 6th Road, Baoan District, Shenzhen CN addres: 深圳宝安82区新安六路华丰金融港B座6层

Guangzhou (Business center): Room 403, Linglanduhui, Huaying road, Jiahe Wanggang, Baiyun district, Guangzhou CN address: 广州市白云区嘉禾望岗华英路岭南都汇403

Additional

SDK, API

Use cases

IP Decoding

SRT Transmission

P-P Decoding

Broadcasting

Summary of content (6 pages)

PAGE 1
FHD Decoders The S9110D Series based decoders were designed for H.264/ H.265 IP (RTMP/ RTSP/ RTP/ HTTP/ HLS/ UDP/ SRT), MPEG1, MPEG2, MPEG4, SL hyperlink (P-P), VP8/ VP9/ AVS/ AVS+ decoding Use cases IP Decoding SRT Transmission P-P Decoding Broadcasting Input H.264/ 265 IP (RTMP/ RTSP/ RTP/ HTTP/ HLS/ UDP/ SRT),MPEG1, MPEG2, MPEG4, SL hyperlink (p-p), SRT, VP8/ VP9/ AVS/ AVS+ (compatible with 4K stream) Accessibilities Power- 12V 2A For S9110D Consumption: 2.
PAGE 2
Ⅰ: Interfaces USB2.0/ 3.
PAGE 3
Ⅱ: Configure network DHCP suggested for new customer or will use it in different networks, so network configuration can be ignored if parameter of the stream configured. If not DHCP enabled by default, please follow the following steps to configure the network for streaming Procedure 1- Enter network setting 2- Enter “Properties” 3- Choose IPv4 4- Enter current IP address and DNS (if don’t know the DNS, use 8.8.8.8) 5- Add another 192.168.1.x based IP address.
PAGE 4
Ⅲ: UI & Configuration Figure 2.1 Figure 2.4 Status (F2.1) For standard protocol ( RTSP, RTMP, HTTP...) (F2.2) Directly input the stream URL, for example, rtsp://192.168.1.168:554/HDMI Multi-view (F2.2) The decoder supports 4 sources multi-view, it means 4 streams are allowed to decode simultaneously Figure 2.2 Network (F2.3) Private protocol (F2.4) HAIWEI private protocol based transmission, enabling the transmission by inputting the IP address of the encoder in intranet, for example: 192.168.1.
PAGE 5
P-P Transmission Like the picture on the let side (Figure 3.1), there are two modes to get the transmission working 1- In intranet Get the ID by ARP scanning Figure 3.1 2- Manually input Manually input the UID, the ID can be founded on the “LiveX” SRT Transmission Like the picture on the let side (Figure 4.1), there are two modes to get the transmission working Figure 4.
PAGE 6
System settings Rebot- reset- change password- upgrade- check firmware version - set up timing reboot (F 5.1) Figure 5.1 PTZ & RS485 (F6.1) Figure 6.