Specification Sheet

ManualsBrandsHaiweiTech ManualsElectronicsH.265 H.264 4K Video Audio Decoder IP Camera Decoder RTMP SRT M3U8 UDP to HDMI CVBS BNC Decoder for Advertisement Display, Decoding Video Encoder, Decoding IP Camera

UHD Decoders

he IP decoders allow H.264/ H.265 IP (RTMP/ RTSP/

RTP/ HTTP/ HLS/ UDP/ SRT), MPEG1, MPEG2, MPEG4,

SL hyperlink (P-P), VP8/ VP9/ AVS/ AVS+ decoding, and

then output through HDMI & BNC (analog), 3.5mm audio

Jack/ CVBS. It supports 4096*2160 30, 1080 P/I@ 60,

meanwhile, RS485 supported (I&O- input and output)

Input

Output

H.264/ 265 IP (RTMP/ RTSP/ RTP/ HTTP/ HLS/ UDP/

SRT),MPEG1, MPEG2, MPEG4, SL hyperlink (p-p), VP8/

VP9/ AVS/ AVS+

HDMI: 4096*2160 30/25/24, 3840*2160 30/25/24,

1080P 60/50/ 30/ 25/ 24, 1080I 60/50, 720P 60/50/25/ 24…

CVBS (BNC/ 3.5 MM): NTSC/ PAL

Audio: HDMI/ 3.5mm output in MP3

Accessibilities

Power- 12V 2A For H9110D

- 100V-240V For DR104& DR316

Consumption: 2.8W for H9110D

＜28W- DR104, ＜40W- DR316

Working Environment

-20℃+ 60℃

Humidity

＜90%, non-condensation

Weight

H9110D (Portable) - 0.3kg

DR104 (1U 4ch) - 3.25 KG

DR316 (3U 16ch )- 7.5 KG

Multi-view

1/ 4/ 16* TCP/ IP Input

深圳海威视讯技术有限公司/ HaiweiTech

Shenzhen headquarters (Factory): 6th floor, Block B, Huafeng financial port, Xin‘An 6th Road, Baoan District, Shenzhen CN addres: 深圳宝安82区新安六路华丰金融港B座6层

Guangzhou (Business center): Room 403, Linglanduhui, Huaying road, Jiahe Wanggang, Baiyun district, Guangzhou CN address: 广州市白云区嘉禾望岗华英路岭南都汇403

Additional

SDK, API

Use cases

IP Decoding

SRT Transmission

P-P Decoding

CCTV Decoding

4K screening

Summary of content (6 pages)

PAGE 1
UHD Decoders decoders allow H.264/ H.265 IP (RTMP/ RTSP/ T heRTP/IP HTTP/ HLS/ UDP/ SRT), MPEG1, MPEG2, MPEG4, SL hyperlink (P-P), VP8/ VP9/ AVS/ AVS+ decoding, and then output through HDMI & BNC (analog), 3.5mm audio Jack/ CVBS. It supports 4096*2160 30, 1080 P/I@ 60, meanwhile, RS485 supported (I&O- input and output) Use cases IP Decoding SRT Transmission P-P Decoding CCTV Decoding 4K screening Input H.
PAGE 2
Ⅰ: Interfaces ① LAN- Ethernet port Need to configure the IP gateway of the decoder if need to use it normally. ② LED indicators RED: POWER ON Green: Network GEN IO-1 IO-2 OUT 485A RST LAN LED AV OUT OUT HDMI ② ④ 485B BNC ③ RST- Reset Keep sticking the RST button until the GREEN light off ⑥ ⑦ ① ③ ⑤ (figure-1.1) ④ AV OUT- CVBS out ⑤ HDMI OUT-HDMI out ⑥ BNC OUT-BNC o u t ⑦ RS485 DC 12V GEN IO-1 ⑧ (figure-1.
PAGE 3
Ⅱ: Configure network DHCP suggested for new customer or will use it in different networks, so network configuration can be ignored if parameter of the stream configured. If not DHCP enabled by default, please follow the following steps to configure the network for streaming Procedure 1- Enter network setting 2- Enter “Properties” 3- Choose IPv4 4- Enter current IP address and DNS (if don’t know the DNS, use 8.8.8.8) 5- Add another 192.168.1.x based IP address.
PAGE 4
Ⅲ: UI & Configuration Figure 2.1 Figure 2.2 For standard protocol ( RTSP, RTMP, HTTP...) Directly input the stream URL, for example, rtsp://192.168.1.168:554/HDMI Multi-view Figure 2.3 The decoder supports 4 sources multi-view, it means 4 streams are allowed to decode simultaneously Private protocol HAIWEI private protocol based transmission, enabling the transmission by inputting the IP address of the encoder in intranet, for example: 192.168.1.168 Figure 2.
PAGE 5
P-P Transmission Like the picture on the let side (Figure 3.1), there are two modes to get the transmission working 1- In intranet Get the ID by ARP scanning 2- Manually input Manually input the UID, the ID can be founded on the “LiveX” Figure 3.1 SRT Transmission Like the picture on the let side (Figure 4.
PAGE 6
System settings Rebot- reset- change password- upgrade- check firmware version - set up timing reboot (F 5.1) Figure 5.1 PTZ & RS485 Figure 6.