INSTALLATION INSTRUCTIONS USER GUIDE Vented clothes dryer Model: HDV60A1 and HDV40A1
CONTENTS SAFETY AND WARNINGS 2 INSTALLATION INSTRUCTIONS 5 CONTROL PANEL 12 USING YOUR DRYER 13 CLEANING YOUR DRYER 15 TROUBLESHOOTING 16 IMPORTANT! SAVE THESE INSTRUCTIONS Please read these instructions carefully before using your tumble dryer. The instructions contain important information which will help you get the best out of the device and ensure safe and proper installation, use and maintenance.
SAFETY AND WARNINGS Meaning of symbols on the dryer Warning: Risk of fire/Flammable materials Read the instructions Fire Hazard ! WARNING! ■ Only dry fabrics that have been washed with water. ■ Do not use heat to dry articles containing foam rubber or similarly textured rubber–like materials, dry on ‘Airing’. ■ Do not stop a tumble clothes dryer before the end of the drying unless all items are removed and spread out, in order to dissipate the heat.
SAFETY AND WARNINGS ■ Do not operate this product without the lint filter in place or allow lint to accumulate in or around the dryer. ■ This dryer is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless given supervision or instruction concerning the use of the dryer by a person responsible for their safety. ■ Children should be supervised to ensure they do not play with the dryer.
SAFETY AND WARNINGS Spontaneous combustion IMPORTANT! ■ ■ ■ ■ ■ ■ ■ ■ ■ To reduce the risk of fire in a tumble dryer the following should be observed: Items that have been spotted or soaked with vegetable oil or cooking oil are a fire hazard and should not be placed in a tumble dryer. Oil-affected items can ignite spontaneously, especially when exposed to heat sources such as a tumble dryer. The items become warm causing an oxidation reaction in the oil. This oxidation creates heat.
INSTALLATION INSTRUCTIONS Please read and follow the ‘Safety and warnings’ and ‘Installation instructions’ sections carefully before using your dryer. Unpacking 1 Remove all the packaging. 2 Tilt the dryer backwards and ‘walk’ it off the base one foot at a time. 3 Remove all packaging and accessories from inside the drum and ensure you remove protective covers from the door and console. IMPORTANT! ■ Ensure packaging materials are kept out of reach of children.
INSTALLATION INSTRUCTIONS Venting Correct installation is very important for all dryers to ensure maximum efficiency and safety. IMPORTANT! Never run the dryer unless the airflow system is free from obstruction. There must be adequate ventilation to avoid the back flow of gases into the room from appliances burning fuels, including open fires, when operating the dryer. Exhaust air must not be discharged into a flue which is used for exhausting fumes from appliances burning gas or other fuels.
INSTALLATION INSTRUCTIONS Free standing The dryer stands on the floor and can easily be moved into position. 1 Move the dryer into the desired position. Do not lift the dryer by the top panel. 2 Have a minimum clearance on all sides of at least 20mm. 3 Have a minimum clearance at the rear of 75mm. The spacers from the accessory wall mounting kit can be used to set this distance. 4 Install the dryer on a stable and level floor.
INSTALLATION INSTRUCTIONS 1 2 3 4 5 6 Mounting dryer on wall Determine the position of the dryer on the wall and mark the bracket position. A minimum of 50mm is needed between the top of the dryer and the ceiling for ease of installation. If mounting above a washing machine, allow sufficient room to open the lid of the washer. Fix the wall hanging brackets to the wall securely, ie into the stud. If the studs are too far apart, fit a timber slat to the studs and then mount the brackets to the slat.
INSTALLATION INSTRUCTIONS Stacking installation Your dryer has been designed to be able to be stacked on the top of a Haier front load washing machine, ensure the washing machine is the same width as your dryer. Tools and parts required: ■ Drill and 2.9mm bit ■ Phillips head screwdriver Stacking bracket includes: ■ 2 x Stacking bracket 1 Remove 4 screws at two sides of bottom panel, then install the stacking bracket.
INSTALLATION INSTRUCTIONS Before a rear venting option is installed the dryer must be changed from the front venting factory setup. Remove the outlet grille from the front left-hand side and replace with the outlet cover from the rear left-hand side. These covers should be gently pried at the sides to prevent damage. Internal venting Front venting is the only option for internal venting. The dryer is set up for front venting when it leaves the factory.
INSTALLATION INSTRUCTIONS Electrical connection 1 This appliance must be connected to a 220V-240V, 50Hz, sinusoidal, 10A electrical supply. 2 Uncoil the power cord, remove and discard the plastic pin cover and plug into a power socket. 3 Connect the appliance to an earthed outlet protected by a fuse of suitable capacity. ■ Check the power cord for damage and make sure it is not squashed or twisted when installing the dryer. ■ Always remove the power cord from the power socket by the plug, not by the cord.
CONTROL PANEL A B C D A Start / Pause button After selecting your desired drying cycle by turning the cycle knob, press the ‘Start / Pause’ button to start the cycle, and press it again to pause the cycle. B Indicator light The light will flash when you select a cycle, and it will stop flashing and remain lit when you start the cycle. It will flash rapidly if a fault occurs. C Control dial Rotate the dial to select your select desired drying cycle or turn off the dryer.
USING YOUR DRYER IMPORTANT! ■ Check the lint filter is clean before every load. Ensure it is replaced correctly before using your dryer. ■ Sort and load items into the dryer drum, ensuring no items are in the way of the door. ■ Close the door. ■ Ensure your dryer connect to an appropriate power supply(220V-240V, 50Hz). ■ ■ ■ ■ Preparing your load Check whether the loads have been spun by washing machine. Check pockets for items that could damage your clothes or get caught in the dryer.
USING YOUR DRYER Selecting program Select you desired drying cycle by turning the control dial. Start the dryer Press ‘Start / Pause’ button to start your dryer. Complete the cycle When the cycle finishes, your dryer will stop rotating and the indicator light will flash, you can open the door and remove the laundry. If you cannot remove the items immediately after the cycle ends, the dryer will automatically initiate “wrinkle free” operation for 1 hour.
CLEANING YOUR DRYER Cleaning your dryer Before you start cleaning your dryer, ensure that it is disconnected from the power (ie unplug the dryer from the power socket). Cleaning the control panel and outer surfaces of the dryer Use a soft damp cloth to wipe all surfaces, then wipe dry. Avoid using chemical or scouring cleaners, as these will damage the paint and plastic surfaces of your dryer. Cleaning the inside of your dryer It is important that you occasionally clean the inside of your dryer.
TROUBLESHOOTING Troubleshooting The following is a list of problems you may encounter when using this appliance and some suggestions that may help to correct the problem. If you still have problems, please contact your Haier Repairer. PROBLEM POSSIBLE CAUSES WHAT TO DO Dryer stops working mid-cycle. Power failure. Check the power supply and restart the desired cycle. Dryer has been paused. Touch the ‘Start / Pause’ button to restart the cycle. Dryer door is open. Ensure the door is firmly shut.
0180500689A 2016.
