GEbrillion.com Owner’s Manual and Installation Instructions Appliance Communication Module (ACM) DRM1E3 Safety Information. . . . . . . . . . . . . . 2 Operating Instructions . . . . . . . . . 3 Installation Instructions. . . . . . 4–9 Troubleshooting Tips . . . . . . . 10, 11 Consumer Support Warranty. . . . . . . . . . . . . . . . . . . . . . . 14-15 Consumer Support. . . . . . . . .
IMPORTANT SAFETY INSTRUCTIONS • Before you begin – Read these instructions completely and carefully. • For your safety - Read and observe all warning and cautions. • IMPORTANT – Save these instructions for local inspector’s use. Observe all governing codes and ordinances. • Note to Installer – Be sure to leave these instructions with the Consumer. • Note to Consumer – Keep these instructions for future reference.
Operating Instructions FEATURES DSM gen III Button USB Indicator Light ACM Connection Location 3 03-09-11 Elliott Koehler BUTTON The button is used for ACM control. USB The USB connection is used for factory programming and diagnostics. There are no consumer accessible features provided by the USB connection. INDICATOR LIGHT The indicator light blinks at different rates to indicate network status or the current utility energy value.
Installation Instructions PARTS SUPPLIED 2 Mounting Screws Appliance Communication Module Mounting Bracket GEbrillion.com Owner’s Manual and Installation Instructions DRMU1 Safety Information . . . . . . . . . . . .2, 3 Operating Instructions . . . . . . .4, 5 Installation Instructions . . . . . .6–9 Troubleshooting Tips . . . . . . . . . .10 Consumer Support Consumer Support . . . . . . . . back cover Warranty . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation Instructions 1 SELECT LOCATION TO INSTALL THE ACM. 1. The ACM can be placed on the cabinet near the appliance. 2. The ACM can be placed on the side of the appliance. The magnetic feet will stick to most appliances. 3. The ACM can be placed inside of non-metallic cabinets. 4. Using the supplied bracket, the module can be mounted to the inside of the cabinet or on the wall. Read the instructions that accompany the appliance for specific recommendations.
Installation Instructions 1 SELECT LOCATION TO INSTALL THE ACM (continues): NOTE: If module needs to be placed farther from appliance extension kit DR07X10010 sold separately is available. To mount inside cabinets, drill 3/4” diameter holes in inconspicuous locations for routing the interconnect cable. For built-in appliances, see the template with the appliance for precise locations. WARNING: RISK OF ELECTRICAL SHOCK - Do not drill into electrical wiring inside walls or cabinets when drilling holes.
Installation Instructions 3 ATTACH MOUNTING BRACKET (OPTIONAL) If using the mounting bracket, attach to the cabinet or wall with the screws provided. Wall anchors (not included) may be used for mounting to drywall, tile, concrete or other surfaces. 4 ATTACH INTERCONNECT CABLE 1) Attach one end of the interconnect cable to the appliance. (Electric ranges are shipped from the factory with the cable connected.) See the instructions on the appliance for the exact location.
Installation Instructions 4 ATTACH INTERCONNECT CABLE (continues) 3) Set the ACM on the countertop or attach it to the side of the appliance or bracket. 4) Press the button on the Appliance Communication Module to initiate the network joining process. The indicator light will gradually brighten and then dim repeatedly until joined.
Installation Instructions CARE AND CLEANING Wipe the ACM surface with a clean, damp cloth as needed. DO NOT submerse or hold under running water. TO DISCONNECT THE APPLIANCE COMMUNICATION MODULE You may need to disconnect the Appliance Communication Module from your Nucleus or Smart Meter if there are issues during joining, or if one of them gets replaced. To disconnect the ACM do the following: 1. Disconnect the interconnect cable from ACM. 2. Wait 5 seconds. 3. Plug cable back in. 4.
Troubleshooting Tips Troubleshooting Tips Save time and money! Review the charts below first and you may not need to call for service. Problem Possible Causes What To Do Indicator Light not lit Normal Operation The indicator light is designed to go dark after 5 minutes to reduce power consumption and to avoid attracting attention to the module. Pressing the button will cause the indicator light to flash indicating the electric rate. One flash is a low rate and 4 flashes is a high rate.
Troubleshooting Tips Problem Possible Causes What To Do Module blinks slowly (1 sec on; 1 sec off) after having joined network Module has lost communication with Nucleus or Smart Meter • Disconnect interconnect cable, wait 5 seconds, reconnect interconnect cable. If that is unsuccessful, review the Nucleus screens for more troubleshooting information or contact your utility if connected directly to a Smart Meter. • Try to relocate module so it is on the same side of the appliance as the Nucleus.
Notes 12
Regulatory Information REGULATORY INFORMATION FCC/IC Compliance Statement This device complies with Part 15 of the FCC Rules and Industry Canada RSS-210. Operation is subject to the following two conditions. (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This product has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules.
Limited Warranty for Appliance Communication Module WARRANTY Your use of the Appliance Communicating Module (“Hardware”), online product registration of the Hardware, or your return of the enclosed Registration Card acknowledges that you have read and agree to the terms of this warranty agreement. GE’s warranty obligations for this Hardware are limited to the terms set forth herein.
Limited Warranty for Appliance Communication Module EXCLUSION OF IMPLIED WARRANTIES—This warranty applies only to the Hardware manufactured by or for GE that can be identified by the “GE” trademark, trade name, or logo affixed to it. This warranty does not apply to any non-GE Hardware or any software, even if packaged or sold with the GE Hardware. Software distributed by GE with or without the GE brand name (including, but not limited to system software) is not covered under this warranty.
Consumer Support. GE Appliances Website GEbrillion.com Have a question or need assistance with your Appliance Communication Module? Try the GE Appliances Website 24 hours a day, any day of the year! For greater convenience and faster service, you can now download Owner’s Manuals and order parts. Technical Support GEbrillion.com Expert GE technical support is only one step away. Call 800.220.6899 during normal business hours to speak with an agent. Contact Us GEbrillion.
