Product Info

ManualsBrandsHafele America ManualsElectronicsRF Door Lock

Hafele America Co. 1 Document No.: DIA.DPR.013

Dialock Dept. Document Date: 12/17/2001

(888) 437-7477 Print Date: 2/8/2002

LockerLock Mounting Instructions and Operation, Simple Mode

NOTICE: Any changes or modifications made to the LockerLock will void the user’s authority to operate this

equipment in compliance with FCC regulations.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful interference to radio communications. However, there is

no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the

receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on

a circuit different from that to which the receiver is connected. Consult the factory or an experienced radio/TV

technician for help.

Set-up:

Set-up of the Dialock LockerLock unit begins with unpacking and inspecting the

unit. Remove and discard the box and packing material. Inspect the unit and all

other components for obvious signs of damage. Contact the dialock department

for questions or problems. The following list includes the article numbers along

side the components packed in the set:

• 1 – LockerLock Set Tiris, 231.80.000

• 1 – LockerLock Label, Silver, Blank, 231.81.100

• 1 – LockerLock Instructions Label, Silver, 231.81.200

• 2 - LockerLock Cover Plug, 231.80.200

Summary of content (9 pages)

PAGE 1
LockerLock Mounting Instructions and Operation, Simple Mode NOTICE: Any changes or modifications made to the LockerLock will void the user’s authority to operate this equipment in compliance with FCC regulations. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
PAGE 2
Installation: Begin by locating and removing the battery cover from the bottom of the LockerLock assembly. This component should be partially detached straight out of the box. Choose the correct mounting diagram for preparing the door for installation (see figures 1, 2, and 3 for typical application drawings). Hafele America Co. Dialock Dept. (888) 437-7477 2 Document No.: DIA.DPR.
PAGE 3
Figure 1 Inset door application utilizing a mortised recess and strike plate for securing the deadbolt. Hafele America Co. Dialock Dept. (888) 437-7477 3 Document No.: DIA.DPR.
PAGE 4
Figure 2 Overlay door application utilizing a mortised recess and strike plate for securing the deadbolt. Hafele America Co. Dialock Dept. (888) 437-7477 4 Document No.: DIA.DPR.
PAGE 5
Figure 3 Overlay door application utilizing an angled strike plate for securing the deadbolt. Hafele America Co. Dialock Dept. (888) 437-7477 5 Document No.: DIA.DPR.
PAGE 6
DRILLING DIAGRAM * LH & RH AS SEEN FROM INSIDE OF DOOR. Mount attached diagram to inside of door. Hafele America Co. Dialock Dept. (888) 437-7477 6 Document No.: DIA.DPR.
PAGE 7
After the LockerLock unit has been attached to the door install four AA batteries per the + and – designations on the LockerLock body. Replace battery cover. The two extension hooks on the cover will have to be pressed in as the cover is reseated. Make sure the cover is secured. The unit is ready to be programmed for operation.
PAGE 8
Normal Operation – Programming for Authorized Keys Authorizing a key is accomplished for LockerLock by presenting a key when the unit has been set to the Programming Mode. Activate the Programming Mode for LockerLock by pressing the push button (the red light will be illuminated) and presenting the Green Addition Key. The green LED light will then begin flashing. While the light is flashing, present all user keys by depressing each for a second into the push button.
PAGE 9
internal solenoid. The push button is held in the depressed position during all locked situations. To open the LockerLock, depress the push button with an authorized user key. An audible “click” will be heard (this indicates that the solenoid been released). Remove the key from the push button and the button will spring out releasing the dead bolt. Repeat this process as required. Battery Changing Procedure The expected battery life for the LockerLock unit is an estimated 10,000 lock cycles.