Installation Guide
SAFETY INFORMATION WARNING Read all warnings and instructions prior to installing the device. Failure to follow these instructions may result in property damage or serious personal injury. Before installation, check that this product is compatible with the associate equipment and accessories. Do not use the device for anything other than its intended use. Any use outside the sphere of application specified by HAB Home Intelligence is not approved.
Installation Guide - v1.0 Page 3 ©HAB Home Intelligence, LLC.
1 2 7 6 5 4 3 iblinds Motor 1. 2. 3. 4. 5. 6. 7. Z-Wave Include / Exclude Button Calibration Reset Button Battery Connector Solar Connector String Pass-Through Channel Micro USB Connector iblinds Motor Tilt Shaft 6 6 Window Blind Components 1. 2. 3. 4. 5. 6. Window Blind Mounting Bracket End Cap Tilting Mechanism Tilt Drum Tilt Rod Headrail Installation Guide - v1.0 Page 4 ©HAB Home Intelligence, LLC.
Installation 1. Remove Blind from Window: Tilt the blind slats to the fully open position and then raise the window blind. Remove any window blind valances and remove the blind from the window mounting brackets. 2. Remove the Tilt Rod With your window blind on a flat surface, note the orientation of the tilt drums in the headrail. You want to make sure the tilt drums all have the same orientation when the tilt rod is reinserted. Carefully remove the tilt rod.
5. Choose Power Option The iblinds device has 2 Power charging options. Select the option that best suits you and follow the instructions below. USB SLR BAT [Option 1. Rechargeable Battery with Charge Adapter] A. Install the Charge Adapter The Charge Adapter is installed where the tilt mechanism is removed from. Align the Charge Adapter so the bottom opening of the Charge Adapter sits over the slot where the tilt mechanism was removed from.
. Install the iblinds Motor Once all connections to the iblinds motor have been made, and the proper adapters have been installed, place the iblinds motor in the headrail. The motor should be as close to the center of the window blind headrail as possible. 8. Reinsert the Tilt Rod Make sure the tilt drums are all in the same orientation that they were in during step 2, before the tilt rod was removed. Carefully insert the tilt rod.
Z-Wave Compatibility The iblinds device can be operated in any Z-Wave network, with other Z-Wave certified devices from other manufacturers. All non-battery-operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network. Z-Wave Association Group The iblinds product grouping identifier is 1 and maximum number of devices that can be added to the group is 5.
Operation Control Use your Control Device and control your 3rd Party Z-wave Controller to change the tilt angle of the blinds. (Follow your Z-Wave Controller specific instructions for operating your user control device) iblinds motor will tilt the blinds to any angle between 0-99 0 = Closed Down 50 = Fully Open 99 = Closed Up The User Control Device can be a Cell Phone, Tablet, Remote, Computer or Voice Control using a digital assistant.
Troubleshooting Symptom Cause Solution Power -Battery Power - Test iblinds Unresponsive System malfunction Hold Pass Through Charger push button for 10 seconds to reset the device Z-Wave Hub/Controller Check Controller Distance Associated with a previous network Z-Wave Include Problems System malfunction Power Pass Through Charger not connected Distance System malfunction Z-Wave Exclude Problems Plug battery into proper port Turn battery power switch on Connect 5V Power to USB Port Check 5V Power
Limited One-Year Warranty on Hardware Limited Warranty HAB Home Intelligence offers a limited one-year warranty on the hardware components of its kit. If a defect in the hardware, or any component thereof, appears at any time during the first year after purchase, HAB Home Intelligence will repair or replace (at its option) the kit or the defective component at no cost to you beyond the cost of shipping the defective item to us. Who Makes This Warranty This warranty is made by HAB Home Intelligence, LLC.
Limitation of Liability THE SOLE REMEDIES AFFORDED UNDER THIS WARRANTY ARE REPAIR, REPLACEMENT, OR, IF REPAIR OR REPLACEMENT IS NOT COMMERCIALLY PRACTICABLE OR CANNOT BE TIMELY MADE, A REFUND OF THE PURCHASE PRICE. IN NO EVENT SHALL THE LIABILITY OF HAB HOME INTELLIGENCE RELATED TO ANY PRODUCT EXCEED THE PURCHASE PRICE OF THE PRODUCT. YOUR USE OF HAB HOME INTELLIGENCE PRODUCTS IS AT YOUR SOLE RISK.