CDMA Gateway Instruction (H3G-650) H3 System Co.
< Revision Notes > No.
0. Overview This document describes instructions regarding the H3 CDMA gateway (H3G-650, H3 System) and the related components. This document includes - How to install and configure the H3 CDMA gateway - How to use the H3 CDMA gateway - How to setup a server system for the H3 CDMA gateways 1. Gateway installation 1) Preparation for deployment A. SIM card i. Unscrew and open the bottom cover. And insert a SIM card. B. Gateway configuration i. Turn off the gateway. ii.
A. Configuration software for an admin: Serial No. modification is enabled. B. Items i. Open: Open the serial port ii. Setting: Shall be checked for changing gateway configurations iii. Serial No: Serial number of the gateway. It’s only enabled for the Admin version iv. IP(DNS): DataCollection Server IP or DNS v. Port: DataCollection Server port vi. Devices List: List of paired devices. Types and BT addresses. vii. Delete List: Delete all pairing info. viii. Clear Button: Clear window ix.
F. G. H. I. J. K. 3. Turn on the gateway. The current configuration and paired devices info are shown. Change the parameters and click “Send.” If you want to delete the pairing info, check “Delete List” and click “Send.” Before clicking “Send”, please double check the settings. Turn off the gateway and disconnect the serial cable. Pairing 1) Mode selection switch A. “N”: Normal operation mode B. “P1”: Pairing mode as a slave. Used for A&D weighing scale (UC-321PBT) and blood pressure monitor (UA-767PBT).
devices 0 1 2 3 4 5 vi. vii. viii. ix. x. xi. Off Green On Green On Green On Red On Red On Red On Off Green On Red On Off Green On During pairing process, the “Readings” LED turns GREEN. At successful pairing, the “Readings” LED blinks GREEN 5 times. At failure, the “Readings” LED blinks RED 5 times. The gateway goes to the step “v.” You can pair another device at the same pairing mode successively.
D. Pairing IEM’s blood pressure monitor i. Turn off all mobile devices nearby, especially Bluetooth. ii. Set the mode selection switch at “P2.” iii. Let the IEM’s blood pressure monitor at pairing mode. iv. Count 30 seconds. v. Turn on the gateway. vi. The gateway shows the number of currently paired devices with LEDs for 5 seconds. vii. The “Readings” LED turns GREEN. viii. Wait for about a few minutes. ix. At success, the “Readings” LED blinks GREEN 5 times. x.
i. ii. 4. P2 Mode(Master): The same mode as “P2” mode with the mode selection switch 1. Go to configuration mode. Please see the section “2. Gateway configuration” with “setting” checked. 2. Click “Start” for searching devices. As the result, a list of Bluetooth devices available is shown in “Device List.” 3. Select one device and click “Pairing.” 4. Information about the process will be shown in “Bluetooth Log.” P1 Mode(Slave): The same mode as “P1” mode with the mode selection switch 1.
i. LOG_PATH=C:\gprs\log <= Log file path ii. DATA_PATH=C:\gprs\data <= Data XML file path iii. PORT=65001 <= TCP/IP port D. Change of configuration i. Stop the corresponding windows service ii. Change the configuration file, gprs_config.ini iii. Re-start the windows service E. To start the windows service: At “Windows Service”, select “DataCollection_GPRS” and run. 2) Data files and communication log files A. Data XML files will be generated at the folder defined at “DATA_PATH.” B.
battery="2.63" con_gwtime="20111221132941" con_devtime="20111221132941" /> PAGE 11id="ZHZ306CBY" measuretime="20100101001250" con_gwtime="20111221132941" con_devtime="20111221132941" Glucometer result="103" unit="0" model="1" adapter="1" battery="3.0" BP Monitor (AND) Weight Scale Thermometer BP Monitor (IEM) Oximeter sys="139" dia="091" pul="094" battery="2.63" result="066.80" unit="kg" battery="2.32" otemp=”98.42” btemp=”74.
Regulatory Statements to be included in the Users Guide for Sputnik USA-Federal Communications Commission (FCC) This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
