User's Manual

ManualsBrandsGuilin Feiyu Technology ManualsCamera & PhotoPanoramic Camera Gimbal

Product Overview

Indicator

Status

Handle

Function

button

1/4 inch

screw hole

Panning

Counter

weight

Tilting

Rolling

Upper

clamping plate

Lower clamping plate

Adapter

Adjusting

screw

* The showing G360 camera is only

for reference

Thumb screw

USB cable X1

Batteries

(Type:22650)X1

Life

Right

Joystick

20g counter

weight

30g counter

weight

40g counter

weight

100g counter

weight

Function button

You can using the function button to switch the

working mode, power on or power oﬀ the gimbal.

Please refer to chapter “Modes / Functions”.

Parts List

Long press the selﬁe button, the lens will rotate 180 °,

release to restore.

Self-timer button

Indicator Status

Mode / Status

Blue light ﬂashes once Panning mode

Lock mode / InitializingBlue light constant on

Blue light keeps ﬂashing

Initialization failure /

Malfunction

Blue light ﬂashes for three times Stand-by

Low batteryRed light ﬂashes three times

Red light keeps ﬂashing

Entering stand-by /

Entering power oﬀ

Summary of content (8 pages)

PAGE 1
Product Overview * The showing G360 camera is only for reference Upper clamping plate Lower clamping plate Adapter Tilting Adjusting screw Thumb screw Indicator Status Blue light ﬂashes once Blue light ﬂashes for three times Blue light constant on Rolling Panning Indicator Status Function button Counter weight Mode / Status Panning mode Stand-by Lock mode / Initializing Blue light keeps ﬂashing Initialization failure / Malfunction Red light keeps ﬂashing Entering stand-by / Entering power
PAGE 2
User Guide ! Attention ! 1 (1) Please install the smartphone before powering on the gimbal (2) Please turn oﬀ the power when the gimbal is not in use, then remove the smartphone Charging Please make sure the battery was fully charged before you power on the gimbal ﬁrst time. Option 1: Charging with micro USB cable. Download APP 2 Download "Feiyu ON" and install it.
PAGE 3
（2）Use the up and down sliders to adjust the vertical center of gravity Tip: The screw can be twisted to adjust, please do not twist the adjustment screw out of the slider. Leaning front Leaning after （2）a Leaning right Leaning left Best Balance （2）b Power on / oﬀ 6 Power On： Press and hold function button until the green light is on. Power Oﬀ： Press and hold function button until the red light changes from quick ﬂashing to constant.
PAGE 4
Mode / Function Operation Instructions Function Button Function Single tap Panning Mode / Lock Mode Quadruple tap Reset Reset the tilting axis of the gimbal to initial orientation and initial mode Standby Single tap again to awake the gimbal, or triple tap to initialize the gimbal Long press until the red light ﬂashes quickly Explanation Single tap to switch between panning mode and lock mode Firmware Upgrade (1) Option 1: connect the gimbal with PC via micro USB cable, and then upgrade the ﬁrmw
PAGE 5
Parameters Titling Angle 360° Titling Increments min 2°/s max 75°/s Panning Angle 360° Usage time 6 Hours Rolling Angle Panning Increments 100° Counter weight 20g, 30g, 40g, 100g Adaption Camera with 1/4 inch screw hole, weight 100~300g. min 3°/s max 150°/s 360g（Not including battery, camera or counter weight ） Weight Unit: mm 189mm 165mm 114.5mm 217.5mm 61.5mm DISCLAIMER Prohibit any user for any illegal purpose.
PAGE 6
Instruction Manual V 1.0 G360 Panoramic Camera Gimbal Compatible with Samsung gear 360/Kodak pixpro sp360/Kodak pixpro sp360 4k/Sony FDR-X3000 etc.
PAGE 7
Create More Possibilities For more information, please visit our oﬃcial website: www.feiyu-tech.com Support Email: service@feiyu-tech.com This product is due to follow-up hardware and software updates may occur description of the introduction does not match the actual product features. You can get the latest user manual from the oﬃcial website www.feiyu-tech.
PAGE 8
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.