User's Manual

On
Off
Pad
Pad
On
12V
Ready
On
Off
Pad
Pad
On
12V
Ready
On
Off
Pad
Pad
On
12V
Ready
On
Off
Pad
Pad
On
12V
Ready
USER MANUAL
PARTS & FUNCTION
Chime
Battery compartment
Battery cover
Speaker
Zone LED
Flasher
Zone selector
button
Melody
selector button
Volume control
Function Switch
Cancel
Cancel Button
CODE MATCHING & TUNE SELECTION
Pressing the 'Cancel' Button will stop the chime and light after the unit has
been activated.
MOUNTING
Wall mounded
Put on the desk Top
Chime
POWER
Chime
3 x 'C' size
Deletetheremotebuttononthechimememory
Change the melody/ tone on desired zone
First,Pressandholdthe'Learning'buttonfor3secondstoenterthelearning
mode.Pressthe'Learnbuttontoselectthezoneyouwanttodelete.Press
andholdboththe' Learning' and the 'Melody' button 3 seconds. The
chime will generate a tone to indicate the remote on this zone has
been deleted.
First,Pressandholdthe'Learning'buttonfor3secondstoenterthelearning
mode.Pressthe'Learnbuttontoselectthezoneyouwanttochange.Press
the'Melody'buttontoselectthenewmelody/toneandthenpushtheremote
button.Youwillhearatonetoindicatethemelodyhasbeenchanged.
ID
Zone selector
button
Melody selector
button
BATTERY LOW INDICATOR
If a zone LED light is blinking, it indicates that the battery is low for
this transmitter. You must replace the battery as soon as possible.
If the white flash at the top of the Chime blinks every 5 seconds, this
indicates the receiver batteries are low. You must replace the batteries of the
receiver.
FunctionSwitch
* Chime
* Light & Chime
* Light
MA-810
RoHS
2002/95/EC
FCC Statement:
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
* Reorient or relocate the receiving antenna.
* Increase the separation between the equipment and receiver.
* Connect the equipment to an outlet on a circuit different from that to which the receiver is
connected.
This device complies with part 15 of the FCC rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment.
Note: Modifications to this product will void the user's authority to operate this
equipment.
Step1:Insert the battery into the transmitter to be
used (Doorbell button)
Step 2: Insert the batteries into the receiver
(chime unit).
Step 3:Enter pairing mode for the receiver
(ch ime unit ). Pr ess & hol d the ● zon e
selector button for 3 seconds. The LED in
zone #1 will flash.
Step 4: Press the ● zone selector button again to
move to the zone you wish to pair with. Press
the ♫ m e lody se l e ctor b u t ton to s c roll
through the melodies. Once you hear a melody you prefer, do not press
any button as the melody is set for that zone.
Step 5: Once the zone & melody are selected, trigger the transmitter once to
pair. If successful, the receiver (chime unit) will generate two short
tones. Press the ● zone selector button to exit the pairing mode, the
system is now ready to use.
To stop the Chime while the receiver (chime unit) is alerting press
the reset button.
58mm
'C' S ize
1.5 V
'C' S ize
1.5 V
'C' S ize
1
.5V
Vibration Pad
On/Off
Vibration out
Indicator
DC Jack
Setup
This Bed Shaker must be worked with the Echochime 300 when using the
vibration function.
DC jack
Bed Shaker
On/Off
Vibration out
On
Off
Pad
Pad
On
12V
Ready
12V ready indicator
Pad On inducator
DC jack: If using the Bed Shaker , it must be connected with a 12V 400mA AC/DC
adaptor to this jack.
12V ready indicator: This indicator will light up, when the 12V adaptor is
connected correctly.
Bed Shaker on/off: Slide this switch to turn on or turn off the vibration function.
Pad on indicator: If the Bed Shaker on/off switch is slide to on position, this LED
indicator will light up to indicate vibration function is ready.
Vibration out: Plug the Bed Shaker to this jack.
12V DC
400mA
12V DC
400mA
Using the Bed Shaker, it must
be connected with a 12V
400mA AC/DC adaptor
CAUTION
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.
DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCT