WARNING: To reduce the risk of injury to persons - Use this operator only with Residential Sectional Garage doors. Owner’s Manual ● Please read and understand this manual and safety instructions carefully before installation. ● The Opener WILL NOT CLOSE until the Photo Eye Safety System is properly installed and aligned. ● REGULARLY CHECK and TEST the Opener according to the safety label to ENSURE SAFE OPERATION. ● Retain this manual for future reference.
Table of Contents Introduction Symbols and Icons Inventory Preparation / Door Balance Test Tools Required 2 3 5 5 Assembly Assembling T-Rail Tension the Belt 6 7 Installation Mounting Header Bracket Attaching Rail to Header Bracket and Mounting Door Bracket Mounting Opener to Ceiling Attaching Door Arms Installing Light and Emergency Release Handle 8 9 10 11 12 Wiring Wiring Instructions Connecting Photo Eye Safety System Connecting Door Control Console Connecting Power 13 14 15 16 Adjustment Aligni
Inventory ( Emergency Release Handle + Rope Photo Eye Safety System Opener Unit + Lamp Dome Light bulbs are not included) Door Control included in some models Door Control x2 Screw #6 x 1” x2 Remote Control 1-FDCC Drywall Anchor Push Button 3-FDCC Header Bracket Literature + Safety Labels Clevis Pin Long x1 5/16” x 2-1/4” Door Bracket Hitch Pin — Locking Clevis Pins x1 Door Arms INSTALLATION HARDWARE, LOCATED IN HARDWARE BAG (SHOWN IN ACTUAL SIZE 1:1) x2 x2 x2 Clevis Pin — Door arms 5/16” x
Read and Follow These Important Safety Instructions IMPORTANT INSTALLATION INSTRUCTIONS WARNING — To reduce the risk of severe injury or death: 1. 2. 3. 4. 5. 6. 7. READ AND FOLLOW ALL INSTALLATION INSTRUCTIONS. Install only on a properly balanced garage door. An improperly balanced door has the potential to inflict severe injury. Have a qualified service person make repairs to cables, spring assemblies, and other hardware before installing the opener.
Preparation ! WARNING To prevent SERIOUS INJURY or DEATH: - Before beginning installation of the Opener please complete the following test to ensure that your door is balanced and in good working condition. - A poorly balanced door can cause serious injury and damage to the Opener. - Always have a qualified garage door service technician make any required adjustments and/or repairs to your door before proceeding with installation.
Assembling T-Rail ! WARNING To prevent SERIOUS INJURY: - DO NOT connect power until instructed. - Keep hands and fingers clear from sprocket during operation. - Wear gloves when installing chain/belt and cable. - Keep hands and fingers away from joints and possible sharp edges. ! CAUTION - DO NOT connect power until instructed. - To prevent INJURY, keep hands and fingers away from joints and possible sharp edges. - Wear gloves when installing chain/belt and cable.
Tension the Belt / Chain ! WARNING To prevent SERIOUS INJURY: - DO NOT connect power until instructed. - Keep hands and fingers clear from sprocket during operation. - Wear gloves when installing chain/belt and cable. - Keep hands and fingers away from joints and possible sharp edges. 1 Note: The chain or belt rail assembly comes pre-tensioned from the factory. Tighten until... Tension the Belt 1.
Mounting Header Bracket ! WARNING To prevent SERIOUS INJURY: - DO NOT connect power until instructed. - The Header Bracket MUST be SECURELY fastened to the structural support on the mounting wall or ceiling, otherwise the door may not reverse when required. DO NOT install the Header Bracket over drywall. - Concrete anchors MUST be used when mounting the Header Bracket into masonry.
Attaching Rail to Header Bracket and Mounting Door Bracket ! CAUTION To prevent SERIOUS INJURY: - DO NOT connect power until instructed. - REINFORCEMENT is recommended for fiberglass, aluminum or lightweight steel garage doors BEFORE installing the door Bracket. Contact your door manufacturer for reinforcement options. To Attach the Opener to the Header Bracket 1. As shown in Fig.1, use the packaging carton as temporary support for the Opener. Place the Opener on carton to prevent damage. 2.
Mounting Opener to Ceiling ! WARNING To prevent SERIOUS INJURY or DEATH: - DO NOT connect power until instructed. - Install the Opener at least 7 feet (2.13m) above the floor. - Fasten the Opener SECURELY to STRUCTURAL SUPPORTS of the garage to prevent falling. - If installing Brackets to masonry, concrete anchors (not provided) MUST be used. To Mount the Opener to Ceiling ppor al su r u t c Stru t The three most common installation options are shown in Fig.1-3. Fig.
Attaching Door Arms ! WARNING To prevent SERIOUS INJURY: - DO NOT connect power until instructed. - Keep hands and fingers away from the sprocket during operation. - Wear gloves when installing chain/belt and cable. - Keep hands and fingers away from joints and possible sharp edges. NOTE: The straight door arm must be installed vertically to the door when door is at closed position. 1 Straight Door Arm To Connect Door Arm Follow the steps shown in Fig. 1 1.
Installing Light and Emergency Release Handle ! WARNING To prevent SERIOUS INJURY or DEATH from electrocution: - Disconnect power cord before installing/replacing light bulb. To prevent possible OVERHEATING or damage to Opener: - Use ONLY A19 (E26) incandescent bulbs (100W max.). - DO NOT use short neck or specialty light bulbs. - DO NOT use halogen bulbs. To install light bulb as shown in Fig.1: 1. M 100W Install a standard A19 (E26) 100 watt maximum light bulb. AX 2. Re-attach the Lamp Dome.
Wiring Instructions ! WARNING To prevent SERIOUS INJURY or DEATH from electrocution: - Power MUST NOT be connected until instructed. - NO exposed part of the wire should be visible outside of the terminal for proper connection. Wire from accessories In the following section, the Photo Eye Safety System and Door Control Console will be connected to the Opener. Please read and understand the wiring instructions before connecting wires. 1. Remove the pre-cut skin on the open end of wire from accessories.
Connecting Photo Eye Safety System ! WARNING To prevent SERIOUS INJURY or DEATH from electrocution: - Power MUST NOT be connected BEFORE Photo Eye Safety system is connected and aligned. - The Opener will not operate until the Photo Eye Safety System is properly connected and aligned. - Install the Photo Eyes NO higher than 6” (15cm) above the floor. No part of garage door or other objects should obstruct the Photo Eye Safety System during door-closing.
Connecting Door Control Console ! WARNING To prevent SERIOUS INJURY or DEATH from electrocution: - Power MUST NOT be connected until instructed. To prevent SERIOUS INJURY or DEATH from using the Door Control Console or Push Button and a closing door: - Install the Door Control Console or Push Button within sight of the door at a minimum height of 5 feet (1.5m) above the floor. Make sure it is out of the reach of children and moving parts of door and hardware.
Connecting Power WARNING ! To prevent SERIOUS INJURY or DEATH from electrocution or fire: - Power MUST be DISCONNECTED BEFORE proceeding with permanent wiring procedures. - Garage Door Opener installation and wiring MUST be in compliance with all local electrical and building codes. Make sure the Opener is ALWAYS grounded. - NEVER use an extension cord, 2-wire adapter or modify the power plug in any way to make it fit the outlet. DO NOT OPERATE OPENER AT THIS TIME.
Travel Limit Adjustment— I. UP Limit ! WARNING To prevent SERIOUS INJURY or DEATH from improper Force Adjustment: - DO NOT adjust force to compensate binding or sticking of the garage door. Call a qualified garage door service person to make necessary adjustments in case of binding. - DO NOT increase force beyond minimum force required for closing the door. Too much force will cause improper operation of safety reversal mechanism.
Travel Limit Adjustment— II. DOWN Limit ! WARNING To prevent SERIOUS INJURY or DEATH from improper Force Adjustment: - DO NOT adjust force to compensate binding or sticking of the garage door. Call a qualified garage door service person to make necessary adjustments in case of binding. - DO NOT increase force beyond minimum force required for closing the door. Too much force will cause improper operation of safety reversal mechanism.
Auto Force Adjustment ! WARNING To prevent SERIOUS INJURY or DEATH from improper Force Adjustment: - DO NOT adjust force to compensate binding or sticking of the garage door. Call a qualified garage door service person to make necessary adjustments in case of binding. - DO NOT increase force beyond minimum force required for closing the door. Too much force will cause improper operation of safety reversal mechanism.
Final Adjustments and Testing ! WARNING To prevent SERIOUS INJURY or DEATH from a closing garage door: - The Safety Reversal Test MUST be conducted ONCE A MONTH. - NO ONE should cross the path of moving door during operation and/or testing. - If either Force or Travel limit adjustment is made, the other adjustment may also needed. - After ANY adjustments to the door system, the Safety Reverse Test MUST be performed to ensure the door reverses on contact with a 1-1/2” thick (2x4 laid flat) object.
Programming Remote Controls * (OPTIONAL) ! WARNING To Prevent SERIOUS INJURY or DEATH: - Keep remote control and battery out of reach of children. - NEVER permit children to access the Door Control Console, Push Button nor Remote Controls. - Operate the door ONLY when it is properly adjusted, and there are no obstructions present. - ALWAYS keep a moving door in sight until completely closed. NEVER cross the path of a moving door.
Operating the Opener ! WARNING To Prevent SERIOUS INJURY or DEATH: - READ AND FOLLOW ALL INSTRUCTIONS AND WARNINGS IN THE OWNER’S MANUAL AND LABELS - Keep Remote Control and battery out of reach of children. - NEVER permit children to access the Door Control Console or Remote Controls. - Operate the door ONLY when it is properly adjusted, and there are no obstructions and is in clear sight. - ALWAYS keep a moving door in sight until completely closed. NEVER cross the path of a moving door.
Operating the Opener Door Status vs.
Maintenance Schedule Once a month Maintenance Door balance test, refer to page 4. Safety reverse test, refer to page 20. Twice a year Check chain/belt tension ( refer to page 6 for adjustment if necessary). Once a year - Limit and Force adjustment may be necessary due to weather conditions. Refer to pages 17-19 for adjustment. Conduct Safety Reverse Test after ANY adjustments. - Lubricate door rollers, bearings and hinges.
Repair Parts Installation Parts 1 2 4 3 5 6 Item Part No. Name / Description 1 GUAT-027 Header Bracket 2 GUAT-022 Door Bracket 3 GUAT-023 Hardware Bag (Installation hardware shown on P.3) 4 GUAT-024 Curved Door Arm 5 GUAT-025 Straight Door Arm 6 GUAT-026 Emergency Release Handle & Rope Accessories 1 2 4 5 3 Item Part No.
Opener Assembly Parts 1 8 4 3 2 5 7 10 9 6 Item Part No.
WARRANTY GARAGE DOOR OPERATORS Manufacturer hereby warrants: 1. Garage Door Operators to be free from defects in material and workmanship for a period of five (5) years for motors and one (1) year for Electronics and Mechanics from date of purchase, if installed by an authorized reseller, otherwise if installed by the purchaser one (1) year will apply. 2.
FCC Warning: Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.