deceleration Welcome to uss the DOVE 12E transmitter EVO TBE Press select Elevator on the Fail Safe interface, then press change the status of Servo Held into Fail Safe(/f you want to keep Servo hold status, there is no need to re-set). There is a expanded sub Item blow. Press select 0%, then press Increase or decrease, respectively, the position amount which centers on the neutral point of servo. The available value Is 125%, respectively. 0% The setting methods for other channels are same as above.
deletion DOVE 128 Welcome fo use the DOVE 12E transmitter 3.18 Trainer Two DOVE 12E transmitters working together can execute the training function to meet the requirements for the beginner. The setting method is shown as below: (1) Data copy First, use the wireless copy function between two DOVE 12E to copy the main transmitter's model data to the trainee's transmitter, this promise the model data between two transmitters is same. Refer the copy method to the second part of helicopter “2.
Welcome to uss the DOVE 128 transmitter. deletion DOVE 12E Channel selection:Press select the channel option; Press select the channel(s) which you want to grant to trainee. The you have selected will be activated as “Active”. The channels which are not granted to trainee will be kept Inhibited. The default setting Is “Inhibit”, Press EXT to exit. 3.18 Timer There are two timers which can be set as stopwatch and countdown, respectively. Each timer can be operated by switch or by shortcut.
Malcolm to uss the DOVE 12E transmitter: detention DOVE 12E 10 System Menu All the functional settings, which are relative to the operation system of DOVE 12E itself, are fully integrated in System Menu. They include Language, Display, Buzzer, vibrator, Stick Mode, Stick Direction, Stick calibration, Battery, and About. Below is the boot screen of Airplane: Elevator trim Throttle trim Transmission power display die Battery volt d U k dep event ion 2.
deletion EVE 12E Welcomes to use the DOVE 12E transmitter 1.3 Buzzer warming Press ENT to the Main Menu, press select System Menu, then press ENT to System Menu. Press select “Buzzer” and press ENT to the Buzzer setting Interface. | Buzzer Status (1) Status:There are On and off two status on the Buzzer interface. Pressing move the navigational mark to the status | on | option. Pressing change the ON or OFF status. t includes Throttle Stick Throttle stick, knobs and Tones items under the status is ON.
deceleration Welcome to uss the DOVE 12E transmitter CHEM 12 1.6 Stick Direction Press ENT to get Main Menu, press select System Menu, and then press ENT to the System Menu, press select Stick Direction, and press ENT to get stick direction setting interface. Stick Direction: There are four items available as Elevator, Aileron, Throttle and Rudder. Press select the stick which will change direction, and press change the direction.
deletion Eve TBE Welcome to use the DOVE 12E transmitter 2.1 Mode! Select Press ENT to enter Main Menu and press make Mode! | Model Select Menu is selected. Press ENT to get the Model Menu and press UP TTT or DN fo select Model select, press ENT fo enter the Model Select | Libra setting Interface. 2 ~% Model 2 Press select the mode! you desired, press ENT to confirm 3% Model 3 and the front of selected one. Total 30 medals are optional. 4% Model 4 Press EXT fo exit after finished. 2.
deletion Welcome to uss the DOVE 128 transmitter. DOVE 12E Press ENT to transmit, “Transmitting appears in the interface. Or press EXT to exit. Press EXT to exit after another DOVE 12E received the data. ee Lo ga “Model Transmit {2) Model receiving Press ENT to enter Main Menu and press select Model Menu. Press ENT to enter Model Menu and press select Model Receiving, continue to press ENT to enter Model Receive setting interface. An inquiry information “Are you sure?” will ba shown as below illustration. .
deletion Eve TBE Welcome to use the DOVE 12E transmitter 27 Trim System Trim System is able to finely tune the following six items, respectively: Elevator, Aileron, Rudder, Throttle, Left Trim and Right Trim. The trim range is divided into 20 grades {factory default is set convenient 1o subtly modify the pitch by adjusting the trim range. Press ENT to enter Main Menu and press select Model Elevator Menu. Press ENT to enter and press select Trim System, press ENT to enter setting Interface.