deletion Welcome to use the DOVE 12E transmitter. DOVE 128 (2) Exponential setting Press the “Throttle Curve” setting interface to select Flight Mods “Exponential” setting, Press set “Off” or “On”. The throttle curve will being changed smoothly if select On, Select Off if not need Normal... then the throttle curve will be shown as a line. Exponential (3) Curve setting It includes two items: Point and Output. (3.1) Point setting Press Throttle Curve interface to select Points setting.
detention Welcome io use the DEVI 12E transmitter DOVE 128 {1} Up selling in the Mix fo throttle interface, preach move the navigation mark fo select UP item. Press Ror bl. to Increase or decrease the mix amount when moving the throttle stick upwards. The bigger the amount Is, the bigger the mix to throttle will be. Change the amount from to for the throttle mix direction Reversing. The adjustable range is £125%.
deceleration Welcome to uss the DOVE 12E transmitter EVO TBE “Position 1"," Position 2" are the same setting way as above "position 0°. {2} Automatic setting (2.1) Automatic Setting In the Gyro Sensor interface, press choose “mode” project set, press delectable sets ("Manual set’ and “Automate sot”). Then choose “Automatic” option. (2.2) Channel L The original channel is you want to change to other channels control,you can choose from “output'set (refer fo “2.10 output’). (2.
deletion DOVE 128 Welcome fo use the DOVE 12E transmitter 3.10 Tall Curve This function Is mainly used for amending the reaction torque produced by pitch angle of main rotor blades.in the set flight mode the mix amount can be automatically switched when moving the flight mode (Forevermore.
deceleration Welcome to uss the DOVE 128 transmitter. DOVE ARE 3.11 Dual Pitch The " Dual pitch " should be activated in * Device output * if want to set this function. Seven Point adjustment method is allowed to set up all the pitch curves respective, in each fight mode, which includes Normal flight, Stunt 1, Stunt 2, Stunt 3, Stunt 4, Throttle Curve . "Throttle Curve should be activated if want to use ( refer to 3.
deletion DOVE 128 Welcome fo use the DOVE 12E transmitter {5) Exponential Curve This function can execute the exponential changes, which are set at Dual Rate and Exponential in Function Menu when it is started. If Off is selected, the exponential curve will be changed in the form of fold line. Setting method: Press touch the navigation mark of Exponential to expand | Pen two options: Off and On. the default setting is Off. On is recommended. Please pass EXT key to exit after finished. “60% Exponential 3.
deletion Welcome to uss the DOVE 128 transmitter. DOVE BE {6} Hovering Setting When the above setup finished, the item Hovering should be set as ON and each point of Pitch Curve should be activated at the same time if the PIT Trim needs to be adjusted in fight The points of 4 will move at the same level with the up and down of the PIT when adjusting the Hovering Trim.
deletion Welcome fo use the DOVE 12E transmitter DOVE 128 Pitch curve 100% Auto rotation landing 2B5%F 2.14 Program Mix There are § series of program mix, mix channels and values are adjustable. Setting Method: ENT to infer function menu, then press UP or DN select "Program REX". And press ENT to Program Mix sifting and current status {default settling is “inhibit") interface. Press choose Inhibit, Normal or Curve. Take "program mix 1” for example, there are “normal” and “curve” setting.
Welcome to uss the DOVE 128 transmitter. deletion DEED 12E Down: Mic amount singing when elevator stick moved backward. Press move ths navigational mark io select Down item. Press increase or decrease, separately, the mix amount. it is possible to reverse mix direction through changing the plus or minus sign before amount. The adjustable range Is $125%. Offset Setting This function can make Slave begin to mix through the corresponding Lever switch from a certain point as the starting point.
deletion DOVE 128 Welcome fo use the DOVE 12E transmitter {2.4) Point Setting Press move the navigation mark of Point option. Press Ror L, there are 7 point options including "Point.L", "Point 1 2%, "Point-M", "Point. 3", "Point 4" and "Point H". Select the point you want to set. | (25) Status Setting (There is no Status options when the point is Point: L or Point. H) After selecting the point that you want to set, press move the navigational mark to Status Item.