Welcomes to use the DOVE 12E transmitter. deletion DOVE 128 Crass ENT to transmit, “Transmitting “ appears in the interface. Or press EXT to exit. Press EXT to exit after another DOVE 12E received the data. {2} Model receiving Mods! Transmit ] vv: x Madam: 4 No. 1 Loi Press ENT to enter Main Menu and press select Model Menu. Press ENT fo get Model Menu and press select Model Receiving, continue to press ENT fo enter Model Receive seeing interface.
deletion Eve TBE Welcome to use the DOVE 12E transmitter 2.7 Trim System Trim System is able to finely tuns the following six items, respectively: Elevator, Aileron, Rudder, Throttle, Left Trim and Right Trim. The trim range is divided into 20 grades (factory default is set convenient to subtly modify the pitch by adjusting the trim range. Trim System hn Crass ENT to triter Main Menu and press sslgct Model | Renovator Menu.
Wearisome to use the DOVE 12E transmitter deletion DOVE 128 Press ENT to enter Main Menu, press move navigation mark to select Model menu. Press ENT to enter Model menu function. | Press Device select Option, Press ENT to Device select Flight Main Switch Option antecedent, (1) Flight Main Switch: Fight Extra Winston Crass move navigation mark to Flight Main Switch and Inhibit press select the desired switch.
deceleration Welcome to use the DOVE 12E transmitter DOVE 128 Press select the Function Setting, press Ror L to choose {pp Output the switch, it incidences Inhibit, Active, Gyro, Governor and Pitch the | default setting is Gyro. You can continue to set others items after AUX finishing . MOD sW Function Device Out ET AUX (3) AUX Fr] Press enter AUX interface.
deletion Welcome fo use the DOVE 12E transmitter. Eve GE {1} Setting for fixed ID The setting for fixed ID should be under the status that automatic ID binding is successfully finished, Below is the setting method. Press ENT to enter Main Menu, press move navigation mark to Mode! Menu. Press ENT to enter Mode! Menu. Press select Fixed ID and press ENT fo enter Fixed ID smelting interface.
deletion Comedic to use the DOVE 12E transmitter DOVE 128 {1} No Signal Warning Sensor Setting Press make the navigation mark to choose "No Signal Warning”. Press choose * Inhibit’ or setting Active ig” inhibit"). If you choose "Active", the Radio will alarm when telemetry | i signal lost. Picture as right: No Signal Warming 2) Voltage sating nm There are 3 different types of voltage can be measured. It includes Internal external V1 and V2 which can be monitored two different external voltage( a.
Welcomes fo use the DOVE 12E transmitter. Temperature deletion EVE 128 Press select "Alarm"setiing, press set the alarm temperature value. Press set other items after finishing the setting. T™ Active Alarm Eas {3.3) T2, T3, T4 setting 12 Inhibit Refer to the step of {4) GPS setting BPS Sating There are 4 items including Altitude Typesetter Unit, Eats Type and | Altitude Type Time Zone in the GPS receiver setting interface.
deletion EVD 12E Welcome to use the DOVE 12E transmitter 3.2 Travel Adjust Press ENT fo enter into Main Ms nu. Press move navigation mark to select item Function Menu. Press ENT to enter Function Menu. Press select Travel Just, Press ENT to enter Travel Adjust interface, as below illustration. It shows the Travel Adjust status of one channel: Take ELEV for example, Press move navigation to Rave! Adjust desired item Elevation of U. Press increase or decrease Elevator the servo travel range.
Welcomes to use the DOVE 12E transmitter. deletion DOVE 128 {1} Channel selection Press move navigation mark of Channel, Press set up channels containing Elevator, Aileron and Rudder. Choose the desired channel for setting. {2) Position distinction Press meow navigation mark to desired rifler Position. In the manual mode, the function of Dual rate and Exponential will be executed by the corresponding D/R switch among Post and Post. Take the item Elevator at channel! as an examples.
deletion DOVE 128 Welcome to use the DOVE 12E transmitter Setting method: Press ENT to enter Main Menu, Press move navigation mark to select Function Menu. Press ENT to enter Function Menu.