deletion EVE F7 Welcome fo use the DOVE FY transmitter (2) Delta Press choose Delta in Wing Type. Below ia the graphics of the servos location of the Delta Type. Left Rotation Right Aileron vai Cornet ts ths paps AIL I Recess || Greeting io ths stoat ELEV In Salver Crass move ihe cursor «to point to V-Ta under V-Tall interface Her any inhibit and Active, please choose Active: V-tail is nonadjustable whee the Wing type is Della.
Welcome to use the DOVE FT transmitter dell 242 Power Amplifier The transmission output power of DOVE F7 is adjustable. iris divided info six grades from low fo high. The lower the transmission output power transmits, ths shorter the radio range is, and the longer the stand-by Has will be, the higher the transmission output power, the darer the dare tangs, and the shorter the standby time. Choose the appropriate transmission output power according to the actual situation Press ENT to the Mari Menu.
deletion EVE F7 Welcome fo use the DOVE FY transmitter 2.14 Sensor Setting Betting method: Press ENT to the Main Menu. Press move the point to Mode! Menu, press ENT to Model Many; Press move the cursor—to point ko Sensor Setting, press ENT to Sensor setting Interface. Pres cassia Activate of Inhibit (the default setting ls inhibit), ssh as gross Activate will includes No Signal Naming, Voltage sensor, Temperature sensor, GPS receiver setting ele.
deletion EVE F7 Welcome to uss the DOVE F? transmitter (3.2) Alma Temperature stings Press move the cursor-to point to T1 option, Pres activate the effing. Inhibit will change fo Active and re will be shown. i the Aa temperature values won t be Shawn. Press move the point to Alarm setting, press sat the sigma temperature value. Press set other dens after finishing the staling.
deletion DOVE F7 Comedic to use the DOVE F7 transmitter 3.2 Travel Adjust Press ENT to the Main Menu. Press move the cursor—to point to Function Menu, press ENT io Function Many; Crass move the point io Travel Adjust, press ENT to Travel Adjust setting interface. The interface display a channel's servo travel value status. Press move the cursor—ta plait to "Elevators LU” sting (ELEGY Is sad in the scampi, press R+ or Key, can sst the travel value while the Elevator towards up. The adjustment range :0.0150.
detention Welcome fo use the BEVY FT transmitter : (2) Position Prose move the cursors point to Position stinging, Uses the | corresponding O/R switch to set D/R and exponential function The available positions ane POSE and POST. ELEV is shown in the | toweling example. Use ELEGY DVR switch fo | select the position you wish fo change. {8) Dual Rats Press move the cursor—to punt to Dual Rate setting, press R+ or Key, can sel the “Position” dus! rate vagus. The default setting Is 100%.
deletion Comedic to use the DOVE F7 transmitter DOVE F7 When Throttle Hold switch “Active”, the throttle hooded in the “Throttle Hold position” sifted position. When Thrombosis Hold Switch “Inhibit, the throes hold status released. Pres EXT to exit. 3.8 Throttles Curve Thrills Curve are adjust through 7 points. Press ENT to the Main Menu.
deletion Welcome to uss the DOVE F? transmitter o =] {8} Throttle Stick sifting The switch between Pos § and Pes 1 can be freely realized through throttle slick after the blow amount has been set up. The below set amount is the position of throttle stick as well as the sandwich point. Throttle setting: Press move the cursor—to point to Throttle Sick sealing, Press L to decrease the amount with a lower limit of 0.0% or Inhibit, Press R+ to creepiness $s amount with an ups mit of 100.0%.
deletion DOVE F7 Comedic to use the DOVE F7 transmitter (2) Rudder differential setting V-Tail should be previously sef in Wing Type of Model Menu if the rudder differential function is activated. Refer to °2.11 Wing Type”. On the interface ne of Differential, pass move the point to Channel, And preach Rr to choose Channel fo Rudder, see illustration: (2.1) Setting for Pos © Press move the cursor—to paint fo Pos 0, press Ror L io increase or decreases differential value, respectively.
