Welcome fo use the DOVE F7 transmitter — deletion DOVE F7 The calibration has failed f prose ENT and shew the following interface. Please go back to the STOOD sub menu using EXT and re-start the calibration process. Press EXT io taxi after finished 1.8 About Setting: Press ENT to the Main Menu. Press move the point fo System Menu, pores ENT fo System Mani, Press nova the cursor—to point to About, press ENT to About sating Interface. You can check the current versions of hardware and software.
detention Wainscots to usa the DOVE FY transmitter DOVE F7 Press move the cursor point fo select the model you want 0 be copied as source mode! and press ENT fo confirm, The serial No. and mode! name of Source Mods! wii be shown as Frustration. Than press locate the source model, pass ENT ia confirm. Then an enquirers "Ars you sure?” is popped up as Frustration. Press ENT 0 copy, oF pass EXT to exit. 2.
detention Wainscots to use the DOVE F7 transmitter = Press move the cursor fo point to tha desired mode! No and press ENT, an inquiry “Ave you sure” wil be shown as illustration. Press ENT to reset and EXT to cancel Irony EXT after finished 28 Type Select This transmitter offers a choice of two model types. The options ers helicopter and airplane Press ENT to the Main Menu.
deletion DEV FP Welcome fo uss the DOVE FY transmitter The channel includes four Rems: Elevator, Alston, Throttles and Rudder. Ths factory default is Inhibit. Take Elevator for example Crass Ror L to honchos the Elevator as stick, and then press DN fo move the coruscate point to value of position. i's possible to adjust the stick position via pressing Ror. Press move the courser point fo On option. And then press change the ON status of stick potion Press EXT after finished, 2.
deletion Wainscots to uss the DOVE F7 transmitter DOVE FF Frags mew the cursorily point to Function Selling, press chooses the switch, it insides inhibit, Active, Gyro, Aver. The default setting is Gyro. Crass EXT to exit after the setting finished. 2.41 Swash Type The swash type is grouped into five options: 1 Serve Normal, 2 Servos 180" , 3 Serves 120° , 3 Serves 140° and 3 Servos 90° . Crass ENT to the Main Menu.
detention -Wei come to use the DOVE F7 transmitter {2} Cancslling/Rasstling the Fixed if you wish to sangs ths receiver Fixed [0 mods! beck i random ID, insert the included BIND PLUG into the output terminal BAT before ihe receiver i powered on. Connect SY DC power io the Hottie channel The red LED of the receiver will lash slowly. Remove the BIND PLUG. The Fixed |D code has bean canceled.
deletion Welcomes to use the DOVE F7 transmitter — {2.2) V1 External V1 Press move the cursor point fo Ester the details refers to the illustration Crass move the point to the Alarm Voltage setting. Crass set the value. The settling range is You can continue to set other Hums after you finished, {2.3) External: V2 setting can refer to External V1 setting. Press EXT to back to sensor setting interface to set other options. {3) Temperature sensor The temperature sensor tan measure up to 4 different motors).
deletion {4.3} Eats Type Press select the Date Type un the GPS settling interfaces and it includes DD-MM-Y MM-DADDY and Y-MM-DD. Tessie the desired fem. Welcome to use the DEVI F7 transmitter {4 4} Time Zone Crass select the Time Zola, press set the desired Tums Zone. iE ee ET The Function Menu allows you to customize the sittings for your saved mudslide.
deletion Welcome fo use the DOVE FY transmitter = The Interface display & adjustable channel's name and adjustable tads project. Crass R+ of Can adjust the fine line the servo neutral position. Press UR or IN can salsa the channel you wish to set. Every Chan's! default setting value is 0.0%. The adjustment ranges are as below: 082.5% ~UB2 5% Saar Pitch LB2.5% ~HBZ.6% oil 62.5% ~HB2 5% Axa TILES R62 5% ~L62 5% Press EXT to exit. 3.
deletion (5.2) Stunt 1, stunt 2 and Throttles Hold settings pens refer to above Norma! Fight settings. Pres EXT to exit 3.5 Throttles Hold if the throttle hood function is activated in the function settings menu, it can be operated by the Throttle Hold switch. The permitted setting range is from 20.0% fo 50.0%. The default sating is INH (uninhibited.
deletion Welcome 2 use the DOVE F7 transmitter CELL {8.1} Point selling Pregame Throttle Curve interface to select Points selling. Press Re+ to expand 8 fist including seven points: “Point-L°, "Point-17, "Point-2", “Point M7, "Point 3°, "Point" and "Polnt-H®. (3.2) Status setting After above setup, press DN to select Status setting, press set inhibit or Active. Lactose inhibit Ff keeping the current value {the default setting a Inhibit). Select Active for changing the above points’ value Paint.
detention Welcome io use the DOVE F7 transmitter Crass sslsct Switch em, press ENT to confirm. Hers are Ways on, Normal Mode, Stuart, Stunt and Largish SW elo settings. After setting finished, press EXT to back tn MIX to Throttles interface. Baronial or Rudder can be sat via pressing DN. {4} The setting of Aileron or Rudder, avd Mix 0 Throttle car be reformed to Elevator effing. Press EXT io exit.
deletion Welcome fo use the DOVE F7 transmitter FE] {2.4} Status Turn the Switch “Flight Mode® or “Thrall Hale”, the status set display present fight mode position. There are “Normal Mode, "Stunt 1°, "Stunt 2, "Throttle hold” sets. "Throttle hold? need to Active (refer to “3.5 Theorist Hold") Normal Mods Press UPON fo shoves “Normal Mode”, precise R+f.oan creepiness or decrease the values individually. the GYRO have "NOR mode and "VACS” mode, when ihe value i lower than 50%, iris "NOR" mode.
detention DOVE £7 Welcome to use the DOVE F7 transmitter {3) Elevator Tha function is based on the three or more saves which is choosiness to the 2 11 Swash Type) The selling method is same a5 above. {4) Pitch The function is based on the two of mots servos which is chovsed(rafer to the 2.11 Swash Type). The setting method is same as above. (5) Exponential This function can outsets the exponential changes, which are set af Dual Rasta and Exponential in Function Mani when it is started.