declension Welcome to use the DOVE F4 transmitter DOVE Fa 2.41 Fixed 1D Using the Fixed 1D function allows users io create a unique relationship between transmitter mode! data and the ear responding model's receiver. it significantly spreads up the binding process and also prevents mistakenly flying an aircraft with the incorrect transmitter mods! selected.
detention DOVE Fg {2} Voltage Welcomes to usa the DOVE F4 transmitter There are 3 different types of village can be measured. If includes Internal §V, Textual V1 and V2 which can be monitored twa different textual battery) respectively. Once the measured voltage is lows than the setting value, the Radio will alarm. {2.1} Receiver Overpower Feeding Voltage) Alarmed value can be settled as Voltage setting: press DN fo move the cursor—in point to Voltage pinion on the Sensor selling interface.
deceleration EVE Fa Welcome to use the DOVE F4 transmitter {8) GPE Seining There are 4 rems including Allude Type, Speed Unit, Date Type and Time Zone in the GPS receiver selling interface. Meting: Press ENT io the Main Menu. Press move the ~ point to Mods! Menu, press ENT to Mods! Menu; Press move | GPS Salting 7.
deletion EVE F4 Welcome to uss the DOVE F4 transmitter Press move the cursor—to point to "Elevators D” selling, press R+ or Key, can set the travel value while the Elevator towards down. The adjustment range Factory default setting: 100.0%. The settings for all channels, Aileron, Throttle, Rudder can all be set using this process. Crass EXT io exit. 3.% Sub Trim NOTE: Sub Trim is used to fine tune the serve neutral position during setup.
deceleration Welcome to use the DOVE F4 transmitter EVE Fa 3.5 Throttle Curve Thistle Curve are adjusted through 7 points. Press ENT fo the Main Menu. Press move the point te Function Menu, press ENT to Function Menu; Press move the point to Throttle Curve, press ENT to Thole Curve setting interface. Throttle Curve TAY Throttle Curve §7.
deletion EVE F4 Welcome to usa the DOVE F4 transmitter (5) Switch Selection When the fem Throttle Stick is set in Inhibit, it is possible to switch between Pos 0 and Pos 1 by Switch. Crass moves the cursor--oi point to "Swiloh™. Press ENT to enter into Switch selection interface, press move the cursor—to point to the dastard item. Crass ENT, the | Thole Curve 174V || Switch 7av desired item whose left side will be changed Outset 50.0 ~ § And Info “1” from “0°.
deceleration Welcome to use the DOVE F4 transmitter DOVE Fa 2} Rudder differential sett @ u or afferent a ae i ven . Differential 174v Y-Tail should be previously set in Wing Type of Mode! Menu if the rudder differential function is activated. Refer ts “2.11 Wing Type’. On the interfaces | — Channel of Differential, press move the point to Chan net, Rudder the Channel item will show the present studied channel Is “Rudder”. The Pos 0 0 system default is not available to setup. Pos 1 (2.
deletion Welcome to use the DOVE F4 transmitter Pres UP or DN, there will be setting for Point-1, Point-2, Point-3, Point-Lat, Pointless, refer to the smelting method as DEV Fa Balance 174v Balance 174v Chan's! Channel Afternoon Alston Point < Right Paint < Right Point Right Point Right . ORE bit — Stave 3.8 Alter an to Rudder Mix above. Crass EXT after fished it. This function is possible to executes the mix of aileron to rudder, which is controlled by switch. Setting meted: Press ENT to the Main Menu.
Welcome to use the DOVE F4 transmitter Rudy to Alec. 174V = Elevator Pos 0 oof Elevator Pos 0 Right a deceleration EVE Fa {1} Elevator setting {1.1} Elevator Pos © Leftward settling Pres move the point fo "Elevator Pos 0 Leftward sating” Hem, and press Ror L fo change the value and the Elevator mix amount when operating Rudder leftward. The mix direction wii be revised by changing the sign of plus or minus beef the values. The adjustable range Elevator Pos 1 Left 9 is £126%. {1.
deletion Welcome to use the DOVE F4 transmitter EVE F4 Master 74v [> Elevator Aileron Throttle Rudder $ Elevator (1.2) Slave channel setting: {1.1} Master channel setting Press move the curse--to point to Master Channel setting, press ENT to the Master Channel! setting interface. Press move the point to the desired Master Channel, press ENT to confirm and press EXT to be back to Program Mix 1 interface.