deletion DOVE-85 Welcome to use the DEVOLVES transmitter 3.2 Travel Adjust Touch the Leon i to ante Function Mani and then click £3 to enter the travel duet Interface. Touch the navigation mark of the desired Item to Increase or decreases the servo travel range. The trim tangs is from 0.0% to 150.0%. The factory default is 100.0%. Click the Leon j% to exit 3.3 Sub Trim Sub Trim can parallel to move the neutral point of the servo.
Welcome to use the DEVOLVES transmitter. d Mention DOVE-85 Setting method: Touch the Icon = fo enter Function Menu and then click [1 to enter the Interface dual rate and exponential Interface. (1) Channel selection Touch the navigation mark of Channel. An expansion list pops up, which contents Elevator, Aileron, and Rudder. Chooses the desired channel for setting. (2) Position selection Touch the navigation mark of Position.
deletion ‘Welcome to use the DEVOLVES transmitter {4) Exponential adjustment It Is possible to adjust the exponential output value of the servo at that point, which Is set up In step “(2) Position selection”, by touching the navigation mark of Exponential (5) Automatic setting Under working with Flight Mode, it is possible to switch the dual rate and exponential, which are set in above “(3) Dual Rate adjustment” and *(4) Exponential adjustment’, respectively.
Welcome to use the DEVOLVES oo deletion DEED-85 Under Throttle Hold muted on (pull the Throttle Hold lever forward), when moving the throttle stick to the point set by Cut Position from high to low, the throttle enters the locked status. That means the throttle is locked at the point set by Hold Position. If pushing Throttle Hold lever, the throttle locked status Is released. Click the Icon £4 fo exit after all the settings are finished. nit 3.
deletion DOVE-85 (3) Flight mode Hers are total three flight modes: Normal Flight, Stunt 1, Stunt 2, the curve of which can be respectively set in their corresponding flight mode. The setting method is same with “(2) Curve Setting” above. Click the icon £3 to exit. Welcome to use the DEVOLVES transmitter 3.7 Mix to Throttle This function can keep the man rotor blades running at the certain revolution caused by the changed load when operating the aileron servo, elevator servo, and rudder servo.
Welcome to use the DOVE-85 we deletion Note: {1) Confirm before flight: whether or not the mix amount set above reaches the desired fight effect, and whether or not all the actions are right in various fight modes. (2) It is unnecessary to use this function when Governor is taken to control the revolution. 3.
fondle (3) Flight mode selection All the flight modes are shown In the right Interface which Includes Normal Fight, Stunt 1, Stunt 2, and Throttle Hold. Throttle Hold Switch should be activated In Device Select (Refer to “2.8 Device Select’). Click the left or it navigation mark of the flight mode, which you want to automatically adjust, to decrease or Increase the amount of gyro gals, respectively. If the gyro you use has two modes of NOR or VACS, when the amount is less than 50 0%, NOR mods is activated.
deletion Welcome to use the DEVOLVES transmitter DOVE-85 (2) Elevator Mix This function is base on “Swash Type” who chose 3 servos or above( Refer to “2.10 Swash Type”). Method is same as above. (3) Mix setting for multi servos This function Is used for two or more servos selected (Refer to “2.10 Swash Type”). Method Is same as above. (4) Exponential setting This function can execute the exponential changes, which ars set at Dual Rate and Exponential In Function Menu.
deletion Welcome to use the DEVOLVES transmitter (2.2) Status setting Touch the navigation mark of Status and expand Into two options: Inhibit and Active. Click Inhibit for keeping the currant amount of the selected point (the factory default setting Is Inhibit); Click Active for changing Its current amount with a drop down of Output popped up. (2.3) Output setting Touch the left or right navigation mark of Output to decrease or increases, respectively, the output amount with a range from -100% to +100%.
Mention Welcome to use the DEVOLVES transmitter DEED-85 Throttle curve Pitch curve 100% 100%) pam so sox Throttle curve 100% 100%) 5%: 75% Fal 0 50% oh 50%, Pitch curve 100% 12° 5% +5" enn ET Son 24, o% 3.12 Program Mix There are total eight sets of Program Mix. It is possible to freely set the channels and their amounts which you want to select and amend, respectively. Setting method: Touch the icon i to enter Function Menu, and then click ito enter the program mix Interface.
detention Ee 8s Welcome to use the DEVOLVES transmitter (1) Setting method for Normal in Program Mix 1 Touch the fem Normal in Program Mix 1 and expands an inquiry “All Servos Hold?" Click OK for all the servos will be locked at the current statuses; click Cancel for unlocked. Enter the next interface after clicking. (1.1) Master channel setting Touch the navigation mark of Master and expands a delectable drop down menu. After clicking the desired channel, the channel name will be shown in Master.