deletion Welcome to use the DOVE 7E transmitter DOVE 7E 2.10 Device Output Device output can set up the output switches respectively. It can activate, inhibit or use other functions. There are MOD switch, Hold switch, SOPS, SP, 8PS2, SP, = Press ENT to enter Main Menu, press move navigational mark to Model Menu. Press ENT to enter Mode! menu. Press select Output device and press ENT to enter Output device Interface. Below three items can be adjusted: Gear, Flap, AUX.
deletion DOVE JE Welcome to use the DOVE 7E transmitter 2.11 Wing Type Wing Type is grouped into Normal, Flapper, Delta and V -Tail. Wing Type selection: ng pe i Press ENT to enter Main Menu, press move = navigation mark to Model Menu. Press ENT to enter Mods! Whe Tenn Menu. Press choose Wing Type, and press fines ENT to enter the Wing Type interface. Press move navigation mark to Wing Type. Press Ror L fo choose | 507] lil Wing Type. The Wing Type are Nona, Flapper and Delta.
deletion Welcome fo use the DOVE 7E transmitter DOVE 7E {4) Dual channels setting Dual Channels can be sst as Elevator, Aileron, Rudder, or Flapper. It is of dual channel output function. The channel, which will be set as dual channel at AUX in Device Output (Refer to “2.10 Device Quipster, should be previously set as Inhibit when the AUX channel is being set. Setting method: Wing Tyre Channel presetting move the navigational Sean mark to tem Dual Channels In the Interface of Wing Type.
deletion Eve TE Welcome to use the DOVE 7E transmitter Press choose the ID code setting and press ENT to confirm. Press choose the digits. After finished, press DN to move to the next code setting, there are 6 digits can be tested. Press ENT key after the new ID has sen stetted. An inquiry interface of “Are you sure?” pop up. "ID Code Matching will be shown after press ENT. After matching, the interface will be resumed to Mode! Menu.
detention Welcome to use the DOVE 7E transmitter DOVE 7E Press slacks the Alarm Voltage setting,press set the value. The range Is you can continue to set other items after you finished (2.2) Textual V1 Press UP or DN enter to Textual V1 setting Interface. Press activate the V1,the details refers to the Illustration. Press select the Alarm Voltages setting. Press set the value. The setting range Is. you can continua to set other items after you finished. (2.
deletion Welcome to use the DOVE 7E transmitter DOVE 7E (4.1) Attitude Type Crass select the Altitude type on the GPS setting interface and it's Absolute and Relative. (4.2) Speed Unit in Press select the Speed Unit on the GPS setting relative. Select the desired item. (4.3) Date Type Press select the Date Type on the GPS setting Interface and It Includes DD-MM-Y ,MM-DADDY and Y-MM-DD. Select the desired em. {4.4) Time Zone Press select the Time Zone , press set the desired Time Zone. Ln (4.3) Date Type (4.
deletion Welcome fo use the DOVE 7E transmitter DOVE 7E 3.2 Travel Adjust Press ENT to enter into main menu. Press move navigation mark to selected item Function menu. Press ENT to enter Function Menu. Press select Travel Just, Press ENT to enter Travel Adjust interface, as below illustration. It shows the Travel Adjust status of one channel: FE Take ELEV for example, Press move navigation SE to desired item Elevation of U. Press increase or oo ann: decrease the servo gravel range.
deletion DOVE TE Welcome to use the DOVE 7E transmitter (2) Position selection Press move navigation mark fo desired Item Position. In the manual mods, the function of Dual rate and Exponential will bs executed by the corresponding MOD switch among Post and Post. Take the item Elevator at chanson as an example, It's possible to shift between Post and Pos 1 via pushing or pulling the MOD switch. [ial Bate ard Bal Dual rate adjustment Press move the navigation mark to desired Be Bt oo item Dual Rate.
detention Welcome to use the DOVE 7E transmitter DOVE 7E (3) Throttle Switch setting It's Invalid for setting, the factory default Is HOLD switch which will be shown in the status item. When the Throttle Hold switch is ON, data under the Throttle Hold can not be amended until Throttle Hold switch to be OFF, and the hold status Is changed. Press EXT to exit after setting up finished. 3.6 Throttle Curve Throttle Curve are adjusts through 7 points.
deletion DOVE 7E Welcome to use the DOVE 7E transmitter {4.3) Output setting There is a expand tier “Output” after select Status Active, press select Output setting, press decrease or increase, respectively, the output value. The adjustable range is from 0.0% to 100.0%, The curve graph In right will be change accordingly. Lhe re Hale ne i Pol = Sadie in 14 Fit = aoe = Lane Outed (4.2) Status setting (4.3) Output setting {4.