deletion DOVE SE Welcome to use the DOVE 7E transmitter (3.1) Adjustment for Point Press Throttle Curve interface expansion list including “-L" “17, “27, “M", “ pressing Rory. re the navigation mark to desired item Point. Press R, an |” and “-H" seven points is shown and can be selected via {3.2) Status adjustment Press move navigation mark to Status and press choose Inhibit or Activate. Click Inhibit If you don't amend the amount of the selected point. The factory default Is Inhibit.
deletion Welcome to use the DOVE 7E transmitter DOVE 7B (2) Down setting In the interface of Mix to Throttle, press move the navigation mark to select Down item. Press Ror L to increase or decrease, respectively, the mix amount when moving the throttle stick downwards. The blogger the amount Is, the bigger the mix to throttle will become. Change the amount from to for the throttle mix direction Reversing.
deletion 5 SE Welcome to use the DOVE 7E transmitter {2) Automatic setting {2.1) Automatic Setting In the Gyro Sensor interface,press UPEND to choose “mods"project set,press RIL to delectable sets (“Manual set” and “Automatic set”). Then choose “Automatic” option. {2.2) Channel The original channel is “AUX" if you want to change to other channels control,you can choose from “output’set. (refer to “2.10 output’), (2.3) Switch:there is no use in the Automatic Setting. (2.
deletion Welcome to use the DOVE 7E transmitter DOVE 7B 3.10 Swash Mix This function, which can ba executed through flight mods, Is used for amending the variation caused by swash plate movement, when the aileron or elevator Is working. Press the “ENT” to enter Main Menu and then press choose the navigation mark of enter Function Menu. The interface will show the Swash Mix Setting after press the “ENT” . The “Swash Mix" item is only effected after choose the two or more servos in “2.
deletion DOVE SE Welcome to use the DOVE 7E transmitter (1) Flight mode. Press enter the Flight Mode at the interface of Pitch Curve,and then move the switch of fight mode, the state of fight mode will be shown. The Pitch Curve can be set at the current state. There are “Normal Mode", “Stunt Mode” and “throttle hold” 3 flight modes. The “Normal Mode” Is made as an example for your reference.
Welcome to use the DOVE 7E transmitter deletion DOVE 7& Throttle curve Pitch curve 100% 75% Flight mode Pitch curve 100% 12 75% +5° Profanation landing BELA 3.12 Program Mix There are 8 series of program mix, mix channels and values are adjustable. Setting Method: Press ENT enter to main menu. Press UP or DN, FUNCTION is flashing, press ENT to enter function menu, then press UP or DN select “PRGMX". And press ENT to program mix setting and current status (default setting Is “Inhibit) Interface.
deletion 5 SE Welcome to use the DOVE 7E transmitter (2) Soave channel setting Press move the navigational mark to select Soave option and press ENT to Soave interface. Pressing UP (1.1) Master channel setting (2) Slave channel setting (1.3) Gain setting Take Elevator at Master as an example. Fo (1.31) UP: Mix amount setting when elevator stick moved upward Press move the navigational mark to salacity Up to stem Press Increase or decrease, separately, the mix amount.
deletion Welcome to use the DOVE 7E transmitter DOVE 7B (1.1) Master channel setting Press move the navigational mark to select Master option and press ENT to Master interface. Pressing select the desired channel and press ENT to make a Press EXT fo be back to Program Mix 1 Interface. (2) Soave channel setting Press move the navigational mark to select Slave option and pass ENT to Soave Interface. Pressing select the desired channel and press ENT to make a Press EXT to be back to Program Mix Interface.
deletion DOVE SE Welcome to use the DOVE 7E transmitter 3.13 Monitor This function can display the current status and positions of all the channels’ outputs, and check the current working status of each channel. Press ENT to enter Main Menu, and then press move the navigational mark to select Function Menu Press ENT to enter the Function Menu and then press select servo Monitor and press ENT to enter the monitor interface for sacking the current working status of each channel. Press EXT to exit . 3.