deletion DOVE 7E (2) Modal raveling Press ENT to enter Man Menu and press select Model Menu. Press ENT to gat Model Menu and press select Mode! Receiving, continue to press ENT to rents Model Receive setting Interface. Welcome to use the DOVE 7E transmitter An inquiry information “Are you sure?” will be shown as below Illustration. hone Press ENT to receive, “Connecting ~ and “Receiving ee " will be shown in series in the interface.
detention Welcome to use the DOVE 7E transmitter DOVE 7E 26 Type Select This device offers two model types menu. They are helicopter and airplane respectively. Press ENT to get Man Menu and press select Model Menu. Press ENT to enter and press select Gyps Select and press ENT to ante setting Interface. Press “ENT” button to get Helicopter and Airplane selections and press select and press ENT to comfort, then press EXT to exit 2.
deletion DOVE 7E Welcome to use the DOVE 7E transmitter Crass inhibit channel in navigation mark, and press R to expand the menu. The channel includes four items: Elevator, Aileron, Throttle and Rudder. The factory default is Inhibit. Take Elevator for example. Press choose the Elevator as stick, then Press DN to move navigation mark to value of position. It's possible to adjust the stick position via pressing Press DN to navigate the OPEN setting,press change the direction of the channel stick.
Welcome to use the DOVE 7E transmitter ~ dentition DOVE 7E (1) Gear Press output Interface can change the GEAR Switch. It Includes MOD SW, HOLD SW, SP SW, SP SW, SP SW, SP SW. Press select the setting switch, The default setting Is HOLD SW. Press select Function Setting after you select the switch,Press R or L can enter the interface of Gear activate, inhibit, Gyro and Governor. The default setting is Activate. You can continue fo set other items after finishing.
detention DOVE 7E Welcome to use the DOVE 7E transmitter Press choose the ID code setting and press ENT to confirm. Press chooses the digits. After finished, press DN to move to the next code setting, there are 6 digits can be tested Press ENT key after the new ID has been tested. An inquiry interface of "Are you sure?” pop up. “ID Code Matching will be shown after press ENT. After matching, the interface will be resumed to Model Menu.
deletion Welcome to use the DOVE 7E transmitter BED FE (2) Voltage setting There are 3 different types of voltage can be measured. t Includes Internal Externalize V1 and V2 which can be monitored two different textual voltage(l . battery) respectively Once the measured voltage Is lower than the setting value, the Radio will alarm. (2.
detention DOVE TE Welcome to use the DOVE 7E transmitter {3.3) T2,73,T4 setting Refer to the step of {4) GPS setting There are 4 items including Altitude Type,Speed Unit,Date Type and Time Zone in the GPS receiver setting interface. Press select the Sensor chatting Interface to enter the GPS setting interface. GE Sad tool i (4.1) Altitude Type La Press select the Altitude type on the GPS RG setting interface and it's Absolute and Relative. {4.
deletion Welcome to use the DOVE 7E transmitter DOVE FE Press move navigation mark to ELEV(take Elevator for shift the status between normal and reverse. Tess are two status for option. And the default setting is Normal. All Channels Reverse Switch like: Aileron, Throttle, Rudder, Gear, Pitch and Aux can be referred to the way of ELEV Reverse Switch. And press EXT 1o ext after finishing setting. 3.2 Travel Adjust Press ENT to enter into Main Menu. Press move navigation mark to select item Function Menu.
deletion DOVE TE Welcome to use the DOVE 7E transmitter Setting method Press ENT to enter Man Menu. Pres move navigation mark to desired tem Function Menu. Press ENT to enter Function Menu, press choose Dual rate and Exponential, Press ENT to enter D/R and Exponential interface. (1) Channel selection Press move navigation mark of Channel, Press set up channels containing Elevator, Allison and Rudder. Choose the desired channel for setting.
deletion DOVE 7E Welcome to use the DOVE 7E transmitter Press activate Throttle Hold function, and expansion list will be shown as Throttle hold status, Throttle hold position and Throttle hold switch. {1) There are two stems under Throttle Hold Status: Active and Inhibit. The factory default setting Is Inhibit. (2) Throttle Hold position In the Throttle Hold interface, press make the Navigation mark to choose “Throttle Hold Position” setting options.