declension DOVE-10 Welcome to use the DOVE-10 transmitter It's possible fo change via pressing R to show Flap Output setting. Devise tin i freebie Caitlin . Flan an Surly Mls Bw Linnet Front Suntan Press move navigation mark io Flap. Press expand the menu Including MOD SW, MIX SW, ELEV D/R, AIL D/R, RUDDY D/R, GEAR SW, SOPS, SP, SP, SP, Sett tim, Right trim, AUX lever and AUX lever. The default setting is MIX SW. es a Pap a Press move navigation mark to Function setting. .
deletion DOVE-10 Welcome to use the DOVE-10 transmitter (5) AUX4,AUXS5 settings please refers to the AUX settings. AUX default setting is AUX knob, AUX default setting is AUX knob. After finished the setting, press EXT lo exit. 2.11 Wing Type ‘Wing Gyps Is grouped Into Normal, Flapper, DELTA, 4-Aileron and V -Tall Wing Type selection: ol na Ripe TE Press ENT to enter Main Menu, press move navigation mark to Model Menu. Press ENT to enter Model | 1115 [Wig Menu.
deletion DOVE-10 Welcome to use the DOVE-10 transmitter 4) Val Press move navigation mark to V-TAIL under V-Tail interface. There are Inhibit and Active, please choose Active. V-tail is nonadjustable when the Wing type is DELTA. Below is the squelch map of servos’ assignment in V-tail: Left amperage: Right perennial Connect to tha output ELEV In Calvert Connect to the autopilot RUDDY In Receiver (5) Dual channels setting Dual Channels can be set as Elevator, Aileron, Rudder, or Chaperon.
deletion Welcome to use the DOVE-10 transmitter DOVE-10 (6.2) Trim Setting: Press select “Dual Channels” setting, press choose the item that you want to select as trim lever in the menu with Inhibit, Left trim, Right Trim, AUX and AUX. nd Tue Lu Wing Tote i nm Tenn beans Lal Thm bold dud bane : {6.1) Mate setting (6.2) Trim Setting Press EXT after setting finished. 2.12 Power Amplifier The transmission output power of DOVE-10 is adjustable. It is divided into six grades from small to big.
deletion Welcome to use the DEC-10 transmitter DOVE-10 Press choose the ID code setting, press cootie the words or number, press UP or DN moves to the next code setting . there are 6 words can be set to ID code. Five ih Stan Hittite Press ENT key after the new ID has been set, An inquiry interface of “Are you sure?" pop up. “ID Code Matching .. will be shown after press ENT. After matching, the interface will be returned to Model Menu. Flan ih Fld 10 Been.
deletion DOVE-10 Welcome to use the DOVE-10 transmitter (2) Voltage setting There are 3 different types of voltage can be measured. It Includes internal Guatemala V1 and V2 which can be monitor two different textual battery) respectively Ono the measured voltage Is lower than the setting value, the Radio will alarm. {2.
detention Welcome to use the DOVE-10 transmitter DOVE-10 randomness = “2 Press UP or DN select R or L set the a ols ali Tio alarm temperature value. Press set other items after finished the setting. oe (3.3) T2,T3,T4 setting Alma : = Refer to the step of (4) GPS setting Thea are 4 items including Altitude Type,Speed Unit, Date type and time Zone in the GPS receiver setting interface. Press select the Sensor setting Interface to enter the GPS setting Interface.
Welcome to use the DOVE-10 transmitter deletion DOVE-10 3.0 Function Menu Function Menu can help you custom adjustments for the selected models. The menu includes such items as Reverse Switch, Travel Adjust, Sub Trim, Dual Rate and Exponential, Throttle Hold, Throttle Curve, Differential, Balance,Gyro Sensor, Nongovernmental to Rudder Elevator to Fiat Mix, Rudder to Allerorn/Elevator Mix,Flap Systemically to Flap Mix, Program Mix, Monitor,Fall Safe, Sensor view, Trainer and Timer. 3.
deletion Welcome to use the DEC-10 transmitter DOVE-10 The interface shows the items and the channels which are adjustable. Press change the neutral point of Servos. The factory default is 0.0%. Press choose desired items. The range as below: eld R62.5% ~L62.5% Gyro 62.5% L62.5% ~H62.5% AUX 62.5% AUX 82.5% ~ 162.5% -62 5% ~+62 5% AUX 62.5% Press EXT to exit after adjustment finished. 3.
detention DEVQ-1Q Welcome to use the DOVE-10 transmitter 3.5 Throttle Hold If this function is set, the switch will be executed by hold switch. The setting value of throttle hold is ranged from the default setting is Inhibit Setting method: Press ENT to enter main menu, Press move navigation mark to select Function menu. Press ENT to enter Function Menu.
deletion DOVE-10 (3) Exponential setting Crass the “Throttle Curve” setting Interface to select “Exponential” setting, Press set "OFF or “ON". The throttle curve will being changed smoothly if select ON. Select OFF if not need then the throttle curve will be shown as a line. (4) Curve setting Including “Point” and “Output *. {4.1) Point setting Welcome to use the DOVE-10 transmitter hls Cine Facilitation Bae il Encephalitic Press Throttle Curve interface to select Points smelting.