detention Welcomes to use the DOVE-10 transmitter DOVE-10 Press choose the requiring AMPLE. Press ENT to confirm then the corresponding Items wii have the®+ "mark In front of the Hems.The AMPLE rate will ba shown on the interface. After the setting, press EXT to exit. 2.13 Fixed ID This setting will bind DOVE-10 with ts receiver In a unique come spending relationship. It will greatly speed up the time of automatic binding when DOVE-10 powered on.
deletion DOVE-10 (2) Fixed ID cancellation Welcome to use the DOVE-10 transmitter Insert the assorted BIND PLUG into the output terminal of BAT before the receiver is powered on, and then plug SV DC power into other output terminal. The red light of receiver will flash slowly. This means the fixed ID code has been canceled. Pull out bind plug DOVE-10 also needs to make relative cancel elation and revision after the fixed ID In receiver Is cleared out.
dandelion Welcomes to use the DOVE-10 transmitter DOVE-10 (2.2) External V1 Press UP or DN enter to External V1 setting Interface. Press activate the V1,the details refers to the Illustration. Press UP or DN select the Alarm voltage setting. Crass set the value. The setting range Is ‘you can confine to set others Items after you finished. (2.3) External: V2 chatting can refers to Textual V4 setting Press EXT back to sensor setting interface after you finished.
devolution DOVE-10 Welcome to use the DOVE-10 transmitter (4.1) Altitude Type Press UP or DN select the Altitude type on the GPS setting Interface and It's Including Absolute and relative. (4.2) Speed Unit Press UP or DN select the Speed Unit on the GPS setting relative. Select the desired tier. (4.3) Date Type Press UP or DN select the of Date Type on the GPS setting interface and it's including YY and Y-MM-DD. Select the desired item. (4.
deletion Welcome to use the DOVE-10 transmitter DOVE-10 Press move navigation mark to Skeletal Elevator for shift the status between normal and reverse. These are two status for option. And the default setting is Normal. All Channels Ra versa Switch lke: Aileron, Throttle, Rudder, Gear, Pitch, Aw, Aux, Aux and Aux can be referred to the way of ELE Reverse Switch. And press EXT to exit after sating finished. 3.2 Travel Adjust Press ENT 10 enter into main menu.
deletion Welcome to use the DEC-10 transmitter DOVE-10 3.4 Dual rate and Exponential Iris possible to use D/R switch to control over the dual rate of elevator, aileron, and rudder after the function of Dual Rate and Exponential is set up. The setting range is 0-125%. Under the help with exponential curve adjustment is not only manually but also automatically able to set up various parameters which are suitable for yourself. Setting method Press ENT to enter man menu.
detention DOVE-10 Welcome to use the DOVE-10 transmitter (5.1) Normal Flight Mode setting: Press the navigation mark of Dual rate and Exponential to select the desired item Normal Flight. Press set the position and the Switch. Only the D/R switch control is valid When Switch Is selected, under the Flight Mode, It's possible for Pos to switch the dual rate and exponential, which are set In above(3) and {4)Exponential adjustment. The settings for Switch, Post, Post, Post and Post ars valid. (5.
deletion Welcome to use the DOVE-10 transmitter DOVE-10 3.6 Throttle Curve Throttle curve are adjusted through seven points, which of all the flight modes can be respectively set. The flight mods includes Normal Flight, Stunt and Stunt. Press ENT to enter main menu, Press move navigation mark to select Function menu. Press ENT to enter Function Menu.
detention DOVE-10 Welcome to use the DOVE-10 transmitter (3.2) Status adjustment (3.3) Output adjustment {3.4) Hovering Adjustment After the setting of (3.3) Output adjustment is finished, it's necessary to set the item of Hovering as On and all the selected points of the throttle curve should be activated if using throttle trim in flight is a must. The five points of in the curve will being paralleled or down with the changing of throttle trim.
deletion DOVE-10 Welcomes to use the DOVE-10 transmitter 3.8 Gyro Sensor This function supply the GYRO sensitivity adjustment,both through switch ‘D/R' to Manual and “flight mode "Automatic switch different sensitivity. Setting method: Press “ENT” Into “main menu”In the Interface;press “UPEND" to choose “functional menu” Press "ENT" Into “functional “UPEND" to choose “Gyro Sensor”, then press “ENT” into “Gyro Sensor” interface. {1) Manual Setting {1.