deletion DOVE-10 Important to correctly mount your radio system In your model. Barlow are some advice on how to Install your equipment. (2) Wrap the receiver with 10mm thickness poly foam and fix it with a rubber band or magic string on your helicopter or airplane. It helps protect the receiver. (3) Iris necessary for you to use rubber grommets and copper sleeves to isolate the vibration from the main body. The mounting screws cannot be over-tightened.
deletion Welcome to use the DEG-10 transmitter DOVE-10 12 0 Installation requirement for DEVOID battery pack Open the battery cover of DOVE-10 transmitter and take out the battery box. Then put & cells AA battery or the same size full charged NIGH battery into the battery box. Please check again to make sure the polarities ara correct. Warming: Do not put the polarities of batteries in the opposite directions.
deletion Welcome to use the DOVE-10 transmitter DOVE-10 Leila All the functional settings, which are relative to the operation system of DOVE-10 itself, are fully integrated In System Menu. They Include Language, Display, Buzzer, vibrator, Stick Mode, Stick Direction, Stick calibration, and About.
detention Welcome fo use the DOVE-10 transmitter DOVE-10 1.3 Buzzer warning Pressing ENT to enter the main menu and pressing move the navigational mark to select system menu then using ENT to enter System menu. Pressing select Buzzer and pressing ENT to enter the buzzer interface. {1) Status: There are On and off two status on the Buzzer interface. Pressing move the navigational mark fo the status option. Pressing change the ON or OFF status.
desertion Welcome to use the DOVE-10 transmitter DOVE-10 Select the stick mode according to the throttle mode showing on the screen. Devi-10 offers 4 stick modes, please refer to “8.0 Switches exchange between left-hand and right-hand throttles. Press EXT to exit after finished. 1.6 Stick Direction Press ENT to get Main Menu, press select System Menu, and then press ENT to the System Menu, press select Stick Direction, and press ENT to get stick direction setting interface.
deletion DOVE-10 2 0 Model Menu Model Menu manages all the model data saved in DOVE-10. It includes Model Select, Model Name, Mode! Copy, Model Transmit, Model Receive, Modal Reset, Type Select, Trim System, Stick Position Switch, Advice Select, Device Output, Swash Gyps, Power Amplifier, Fixed ID and Sensor sifting 2.1 Mods! Select Press ENT to get Main Menu and press make Model Menu is selected.
detention DOVE-10 2.4 Mode! wireless copy Welcome to use the DOVE-10 transmitter The mode! data between two DOVE-10 equipment can be tirelessly cooled via Model Transmit and Mode! Receive in Model Menu. (1) Model transmission Press ENT to enter "Main Menu" and press select "Mods! Menu". Press ENT to get "Model Menu" and press select "Model transmission”, continue to press ENT to ante "Modal Transmit” setting interface.
deletion Welcomes to use the DOVE-10 transmitter DOVE-10 2.5 Modes! reset All the model data can be restored to factory settings via Model Reset. Press the ENT to get Main Menu and press select Model Menu. Press ENT to get Model Menu and press select Model Reset, press ENT to get Model reset setting Interface. It Is possible to store up to 30 models data In the mode! list of DOVE-10 equipment. There are two methods to reset the model data: batch reset and single reset.
deletion DOVE-10 Crass select the trim which will set, press R to Welcomes to use the DOVE-10 transmitter increase the trim value and press L to reduce. For elevator, aileron, and rudder, there are two more options: Normal and Limited, press R or L you can change the setup. “Normal” means the trim is always working although the corresponding stick stays anywhere. “Limited” means the trim Is out of working when the corresponding stick Is at maximum position. Press EXT to exit after finished. 2.
Welcome to use the DOVE-10 transmitter ~~ dentition DOVE-10 2.9 Advice select This setting can help you configure various functional switches, or adjust levers. It Includes Flight Mode Switch, Stunt Trim Select, Throttle Hold Switch, Hover pitch select, Hover throttle select. Press ENT to enter Main Menu, press move navigation mark to select Modal menu. Press ENT to enter Model menu function. Crass select Device Option. Press ENT to Device Option Interface.
deletion DOVE-10 Welcome to use the DOVE-10 transmitter Press slacks the Function setting, press choose the switch, It Includes Inhibit, activate, Gyro, Governor, the default setting is Gyro. You can continue to set others items after finished . Citizen Lon Lon Ce (3) AUX Press enter the AUX interface. Press R or L can change the AUX switch. It includes RUDDY Left trim, Right Timbuktu knockabout knob, The default setting Is RUDDY DiR switch Press move navigation mark to Function setting. Press desired item.